From 2010.igem.org

<partinfo>K238008</partinfo>: virA

We wanted to use this part in our project, but could only obtain unexpected/faulty restriction patterns. Finally we chose to sequence the part, hoping to find the cause for the maintained restriction patterns. Unfortunately we could not approve the sequence of <partinfo>BBa_K238008</partinfo> deposited in the parts registry so that we chose to design our own VirA BioBrick. I strongly recommend using our VirA since it has been approved by multiple means, e.g. restriction patterns and sequencing (<partinfo>K389001</partinfo>).

<partinfo>BBa_K238011</partinfo>: vir-promoter

We wanted to use this part in our project, but could only obtain unexpected/faulty restriction patterns. Finally we chose to sequence the part, hoping to find the cause for the maintained restriction patterns. Unfortunately we could not approve the sequence of <partinfo>BBa_K238011</partinfo> deposited in the parts registry so that we chose to design our own VirA BioBrick. I strongly recommend using our VirA since it has been approved by multiple means, e.g. restriction patterns and sequencing (<partinfo>K389003</partinfo>).

<partinfo>P1010</partinfo>: ccdB-gene

The ccdB gene targets the gyrase of Escherichia coli and is lethal for all E. coli strains without the gyrase mutation gyrA462 ([http://openwetware.org/wiki/CcdB Openwetware]). The ccdB BioBrick is used for the 3A-assembly as a positive selection marker. We transformed this BioBrick into E. coli JM109, DH5α, TOP10, XL1-Blue, EC100D and DB3.1. E. coli JM109, XL1-Blue and DH5α seem to be ccdB resistant because there were as much colonies after P1010 transformation as observed with DB3.1. The P1010 works as expected in E. coli TOP10, EC100D (no colonies after transformation) and DB3.1 (many colonies after transformation).

It seems that not only the gyrase mutation gyrA462 is causing a ccdB resistance. Also the gyrase mutation gyrA96 gives E. coli a ccdB resistance. This should be kept in mind when assembling BioBricks with the 3A assembly.

<partinfo>K389004</partinfo>: Luciferase from pGL4.10[luc2]

For a comparison between mRFP and luciferase as reporter genes click here.

Some important parameters determined by the characterization experiments are shown in tab. 2. For more information concerning these experiments click on the corresponding link in tab. 2 or click here:

<partinfo>K389011</partinfo>: VirA screening device

Figure 1: Ratio of surviving colonies of E. coli EC100D carrying unmutated <partinfo>K389010</partinfo> and <partinfo>K389011</partinfo> plated on PA agar plates with chloramphenicol, ampicillin and different concentrations of kanamycin. Comparison between cells that were induced with acetosyringone with cells that were not induced.

<partinfo>K389015</partinfo>: VirA/G reporter device with luciferase

Some important parameters determined by the characterization experiments are shown in tab. 3. For more information concerning these experiments click on the corresponding link in tab. 3 or click here:

<partinfo>K389016</partinfo>: VirA/G reporter device with mRFP

Protocols for Cultivation and Measurement

Some important parameters determined by the characterization experiments are shown in tab. 4. For more information concerning these experiments click on the corresponding link in tab. 4 or click here:

<partinfo>K389052</partinfo>: Tightly regulated lac operon with mRFP readout

This construct was plated for plasmid isolation in a lacI^q negative E. coli strain after assembly - and we have never seen such red plates when working with constructs with mRFP downstream of a promoter. This lac operon definitely shows a very high basal transcription, so it is not tightly repressed. It seems that the lacI repressor <partinfo>BBa_C0012</partinfo> is not suitable for this purpose due to its LVA degradation tag or it does not work properly. Another indicator for this assumption is the experience page of <partinfo>C0012</partinfo>.

<partinfo>K389421</partinfo>, <partinfo>K389422</partinfo>, <partinfo>K389423</partinfo>: Sensitivity Tuner amplified Vir-test system

Figure 2: Amplification factor of induced, 50 µM Acetosyringone (red) and not induced (green) modified Sensitivity Tuner <partinfo>K389421</partinfo>, <partinfo>K389422</partinfo> and <partinfo>K389423</partinfo>, Standard deviation shown.

Figure 3: Vizualitation of induced (from left to right) <partinfo>K389421</partinfo>, <partinfo>K389422</partinfo> and <partinfo>K389423</partinfo> sensitivity tuner amplified vir-system.

References

• Behrens B, Eppendorf AG, Laborpraxis, Nr.20, Reinste Plasmid-DNA in nur 9 Minuten.

• http://openwetware.org/wiki/CcdB, CcdB (seen on 10.10.10).

• http://openwetware.org/wiki/E._coli_genotypes, E. coli genotypes (seen on 10.10.10).

• Metcalf, WW et al. (1994) [http://www.sciencedirect.com/science?_ob=ArticleURL&_udi=B6T39-47PNXC3-F3&_user=2459438&_coverDate=01%2F28%2F1994&_rdoc=1&_fmt=high&_orig=search&_origin=search&_sort=d&_docanchor=&view=c&_acct=C000057302&_version=1&_urlVersion=0&_userid=2459438&md5=dfcdeab4c210c1f4ec70de318d013c15&searchtype=a Use of the rep technique for allele replacement to construct new Escherichia coli hosts for maintenance of R6Kλ origin plasmids at different copy numbers], Gene 138(1):1-7.

• Stadler J, Lemmens R, Nyhammar T 2004, Plasmid DNA purification, The J. of Gene Medicine,Vol.6, pp.54–S66