Team:MIT phage results

From 2010.igem.org

Revision as of 06:22, 26 October 2010 by Galbiati (Talk | contribs)

hairy cells and polymerizing phage - results

Experimental Aims
This summer, we pursued three main experimental aims:
  1. to create a system for inducible polyphage formation
  2. to display fusion proteins on the phage coat
  3. to take microscope images polyphage cross-linking

Polyphage formation
Rakonjac and Model (1998) showed that in the absence of pIII, elongation of the phage proceeds without termination, and the assembling phage stay associated with the cells. We were able to reproduce this phenotype with cells transformed with the hyperphage phagemid.

Cells that were transformed with the hyperphage phagemid show a dense mat of many long filaments extending from the cell.
Figure 1   click to enlarge


Figure 1. AFM Image of Hyperphage-Transformed Cell
DH5a-pro cells were transformed with hyperphage, then grown with low shaking for 10 hours, to prevent shearing of the phage. The polyphage are the long rod structures that fan out around the cell. The round artifacts immediately surrounding the cell is likely disrupted membrane, resulting from washing the cells in water instead of a salt buffered solution.


In contrast, when we transformed with hyperphage and our pIII producing plasmid, BBa_K415138, we observed that the polyphage were absent.

Figure 2   click to enlarge


Figure 2. AFM Image of Hyperphage/BBa_K415138 Co-Transformed Cells
DH5a-pro cells were transformed with hyperphage and our p3 generator, BBa_K415138, then grown with low shaking for 10 hours. No polyphage structures are apparent. Presumably, these cells are producing single phage.

Figure 3   click to enlarge


Figure 3. AFM Image of M13K07 transformed cells
DH5a-pro cells were transformed with M13K07 then grown with low shaking for 10 hours. Note the similarity to Figure 2: No polyphage structures are apparent. These cells produce single phage.


Displaying Fusion Proteins
In testing for the incorporation of our fusion into the phage coat, we chose to have M13K07 package our fusion instead of hyperphage. Testing with hyperphage would be difficult because the 100-fold reduction in infectivity (Rakonjac and Model, 1998) and the property of being tethered to the membrane introduce complications in the necessary amplification and purification steps. M13K07 and Hyperphage are equivalent in all other aspects, so M13K07 makes an ideal system for testing the ability of our fusions to be incorporated into the phage coat. We transformed cells with our fusions, infected them with the M13K07 helper phage, and purified the resulting amplified phage, then western blotted with HA and Myc antibodies. We did not induce cultures because our fusions were under control of R0065, a very leaky promoter, and we postulated that the basal level of expression would be enough for incorporation.

In the western blot, we observed signals from p8-Fos* and p8-GR1. The other linkers may require some tuning of induction or additional troubleshooting before we observe incorporation.
Figure 4   click to enlarge


Figure 4. Western Blot of p8-Linkers
Of our fusions, p8-Fos, p8-Base, and p8-GR2 are tagged with Myc, and p8-Jun, p8-Acid and p8-GR1 are tagged with HA. Purified M13K07 and M13KE were run as negative controls (neither have fusion protiens). p8-GR1 was run on the Myc blot as an additional negative control, as p8-GR1 lacks the Myc tag. In all cases, about 10^11 phage were loaded onto the gel.

*Side note: Interestingly, p8-Fos shows a band at the expected 13 kD and another band at 15kD. One speculation is that because we changed an Alanine to a Leucine at the cleavage site (the joining between the p8 leader sequence and the coil), we may have created a fusion that is cleaved at a lower efficiency. This speculation requires additional thought and research, however; it will be considered in the debugging of the other p8-linkers.

Cross-linking

[UNDER CONSTRUCTION]
Construction       Context