Team:Uppsala-SwedenWeek16

From 2010.igem.org

Revision as of 23:13, 26 October 2010

Week-16

Start to apply high fidelity PCR due the construct are getting larger and the regular Taq polymerase may not perform as well as the Phusion Polymerase at this length. Based on the company´s manual, we calculated the

The purpose of this was to get more reliable band when doing a PCR and running the gel.

J1C3, J2C3 and J3C1 was picked to build the K4,K5,K6 based on the gelpictures from 27/8/2010. Therefore we do not proceed with the ligated J-construct from the 16/9 due we have good enough samples from August month

Concentration measurement and swithch the backbone from pSB1C3 to psB1A3

Ligation and transformation according the protocol

Phusion colony-PCR for K1, K2, K3, G1, G2 with Phusion Polymerase

K1 K2 K3 G1 G2

K1 K2 K3 G1 G2

K1 K2 K3 G1 G2

We had unsatisfied results with our colonies fluorescence measurement and we suspected that the LacI protein didn’t suppress the fluorescent protein enough. One possible explanation would that BB_P0412 contains BB_C0012 which is the coding region for the LacI protein were degraded too effectively by the LVA degradation tail. As a consequence the R0010, a LacI promoter suppressing the three plasmids flourescent expression, didn’t bind enough LacI and therefore you could detect some flourescence.

Since J-construct contains the BB_R0010 as well, the K4, K5 and K6 construction were postponed.

Therefore we switch the BB_C0012 to another LacI-coding sequence that excluded the degradation tail., called LacIB115 which is in psB1AK3. With the restriction enzymes ApaI and PstI , both restriction sites surround the LacI coding region for psB1AK3 and I-construct. Afterdigestion of both plamids, you run the gel and cut out the band with LacI (without the degradation tail and the I-construction backbone and assembly those two parts.

Characterization of G2

G1 has been characterized by via length confirmation. However, G2 had yet to be confirmed. A simple reporter system of F2621 and I13504 (GFP gene) was constructed. However, the reporter system failed to be transformed into cells. In order to confirm G2 some other way, two few improvisational constructs were made, codenamed Z1 and Z2:

Z1: P0412-R0010-I13504

Z2: P0412-R0010-I13507

Z1 and Z2 produce GFP and RFP constitutively. If coupled with H1 and H2 respectively, they obtain an upper threshold for their band-detection, but not the lower threshold.

5 LB cultures were prepared to test our G2. They are: G2, H1+Z1, H2+Z2, G2 with H1+Z1, and G2 with H2+Z2. All the LB cultures were inoculated at the same time, in 6 ml LB in culture tubes. The cultures grew overnight in 37°C under 250 rpm.

G2 are the sender cells. H1+Z1 and H2+Z2 are cut-up K1 and K2 constructs without the lower threshold for band detection. In this case, the H1+Z1 and H2+Z2 will show fluorescence only if there is too much AHL. Without AHL, GFP and RFP will be produced constitutively by H1+Z1 and H2+Z2. In the G2 sample, there is no fluorescent plasmid. In the H1+Z1 and H2+Z2 without G2, there should be no AHL in them. Hence, they express GFP and RFP and emit fluorescence. In the G2 samples with H1+Z1 or H2+Z2, there will be excessive amount of G2. So the expected results should be:

From left: G2, H1+Z1, H2+Z2, G2 with H1+Z1, G2 with H2+Z2