Contents 1 Gel Electrophoresis for Amplified Pspac_oid promoter and lacI 1.1 Aim 1.2 Materials and Protocol 1.3 Result 1.4 Discussion 1.5 Conclusion 2 Amplification of Pspac_oid promoter by PCR 2.1 Aim 2.2 Materials and Protocol 2.2.1 PCR 2.3 Discussion 2.4 Conclusion 3 Gel Electrophoresis for Amplified Pspac_oid promoter 3.1 Aim 3.2 Materials and Protocol 3.3 Result 3.4 Discussion 3.5 Conclusion 4 lacI ligation (repeat) 4.1 Aim 4.2 Materials and Protocols 4.3 Discussion 4.4 Results 5 lacI and pVeg spoVG Transformation 5.1 Aim 5.2 Materials and Protocol 5.3 Discussion 5.4 Conclusion

Gel Electrophoresis for Amplified Pspac_oid promoter and lacI

Aim

The aim of the experiment is to perform gel electrophoresis for the two PCR reactions viz. lacI and Pspac_oid promoter which took place yesterday 5th August, 2010 and thus confirm that they were successful.

Materials and Protocol

Please refer to: Gel electrophoresis.

Result

• Lane 1: 1kb DNA ladder
• Lane 2: Plamid pMutin4 containing lacI
• Lane 3: Plamid pMutin4 containing Pspac_oid promoter
• Lane 4: 100bp DNA ladder

	Pspac_oid pormoter	lacI
Size of the Fragment (in bp)	106 approx.	1400 approx.

Table 1: Table represents the size of the fragments represented as bands on the gel in their corresponding lanes.

Discussion

We found a band in the lanes 2 of the correct size but lane 3 did not contain any band.

Conclusion

This experiment shows that the PCR reaction was successful for the lacI fragment apart from Pspac_oid promoter which was present in the lane 3 and did not show any band. As we got a band for lacI, we can conclude that the plasmid pMutin4 is intact. But we still are not getting a band for Pspac_oid pomoter. This could be because of the following problem:

1. Melting temperature could be incorrect.

Amplification of Pspac_oid promoter by PCR

Aim

The aim of this experiment is to amplify Pspac_oid promoter fragment from plasmid pMutin4 for the construction of rocF BioBrick with the help of 2 different Phusion PCR.

Materials and Protocol

Please refer to PCR for Phusion PCR protocol. The details for the 2 PCR reactions are mentioned below:

PCR

Tube	Part to be amplified	DNA fragment consisting the part	Forward primer	Reverse Primer	Melting Temperature (Tm in °C)	Size of the fragment (in bp)	Extension time* (in seconds)
1	Pspacoid Promoter	pMutin4	P1P1 forward	P2P1 reverse	49	106 approx.	15
2	Pspacoid Promoter	pMutin4	P1P1 forward	P2P1 reverse	50	106 approx.	15

Table 2: Table represents 3 different Phusion PCR reactions for the amplification of Pspac_oid promoter, so that it can be ligated together with other fragments for the construction of rocF with the help of Gibson Cloning method.

• The extension rate of the Phusion polymerase is 1Kb/ 30 seconds. Thus the extension time of each and every PCR reaction is slightly different.
• For learning about the rocF fragments, please refer to the Cloning strategy for rocF.

Discussion

All the 2 Phusion PCR reactions were done however, gel electrophoresis will be done later today, to check whether the fragments have actually amplified or not.

Conclusion

Today afternoon, we would be running gel electrophoresis to check the outcome of the 2 PCR reactions and later all the fragments will be ligated with help of Gibson protocol if the fragments have amplified.

Gel Electrophoresis for Amplified Pspac_oid promoter

Aim

The aim of the experiment is to perform gel electrophoresis for the two PCR reactions for Pspac_oid promoter which took place today morning and thus confirm that they were successful.

Materials and Protocol

Please refer to: Gel electrophoresis.

Result

• Lane 1: 100bp DNA ladder
• Lane 2: Plamid pMutin4 containing Pspac_oid promoter at 49°C
• Lane 3: Plamid pMutin4 containing Pspac_oid promoter at 50°C
• Lane 4: 100bp DNA ladder

	Pspac_oid promoter at 49°C	Pspac_oid promoter at 50°C
Size of the Fragment (in bp)	2072 approx.	2072 approx.

Table 1: Table represents the size of the fragments represented as bands on the gel in their corresponding lanes.

Discussion

We found two very faint bands in the lanes 2 and 3.

Conclusion

This experiment shows that the PCR reaction was successful for the lacI fragment apart from Pspac_oid promoter which was present in the lane 3 and did not show any band. As we got a band for lacI, we can conclude that the plasmid pMutin4 is intact. But we still are not getting a band for Pspac_oid pomoter. This could be because of the following problem:

1. Melting temperature could be incorrect.

lacI ligation (repeat)

Aim

We aim to repeat the ligation from week 12-17th July.

Materials and Protocols

Please refer to ligation for protocol. However, we did not do a positive control for this experiment.

Discussion

On Monday we will transform E.coli with the ligation product.

Results

Please refer to 09.08.10 for results.

lacI and pVeg spoVG Transformation

Aim

We aim to transform competent E.coli DH5α with pVeg spoVG and lacI in preparation for Gibson Cloning.

Materials and Protocol

Please refer to transformation for protocol.

Discussion

We expect cells transformed with lacI and pVeg to survive on the ampicillin plates.

Conclusion

Please refer to 09.08.10 for results.