Team:MIT phage results

From 2010.igem.org

(Difference between revisions)
Line 171: Line 171:
<b> Cross-linking </b><br>
<b> Cross-linking </b><br>
Over the course of the summer, we've found that taking AFM images is difficult and time-consuming. Our original plan was to take AFM images of cross-linking hyperphage. After repeated attempts and little success, we realized that we needed to have a fast way of debugging our system.  
Over the course of the summer, we've found that taking AFM images is difficult and time-consuming. Our original plan was to take AFM images of cross-linking hyperphage. After repeated attempts and little success, we realized that we needed to have a fast way of debugging our system.  
-
<br>
+
<br><br>
To facilitate fast debugging, we designed a system that would couple the heterodimerization of GR1 and GR2 to a fluorescent output, via split GFP.
To facilitate fast debugging, we designed a system that would couple the heterodimerization of GR1 and GR2 to a fluorescent output, via split GFP.
<br>
<br>

Revision as of 02:13, 28 October 2010

Phage
hairy cells and polymerizing phage - results

Experimental Aims
This summer, we pursued three main experimental aims:
  1. to create a system for inducible polyphage formation
  2. to display fusion proteins on the phage coat
  3. to demonstrate cross-linking

Polyphage formation
Rakonjac and Model (1998) showed that in the absence of pIII, elongation of the phage proceeds without termination, and the assembling phage stay associated with the cells. We were able to reproduce this phenotype with cells transformed with the hyperphage phagemid.

Cells that were transformed with the hyperphage phagemid show a dense mat of many long filaments extending from the cell.
Figure 1   click to enlarge


Figure 1. AFM Image of Hyperphage-Transformed Cell
DH5a-pro cells were transformed with hyperphage, then grown with low shaking for 10 hours, to prevent shearing of the phage. The polyphage are the long rod structures that fan out around the cell. The round artifacts immediately surrounding the cell is likely disrupted membrane, resulting from washing the cells in water instead of a salt buffered solution.


In contrast, when we transformed with hyperphage and our pIII producing plasmid, BBa_K415138, we observed that the polyphage were absent.

Figure 2   click to enlarge


Figure 2. AFM Image of Hyperphage/BBa_K415138 Co-Transformed Cells
DH5a-pro cells were transformed with hyperphage and our p3 generator, BBa_K415138, then grown with low shaking for 10 hours. No polyphage structures are apparent. Presumably, these cells are producing single phage.

Figure 3   click to enlarge


Figure 3. AFM Image of M13K07 transformed cells
DH5a-pro cells were transformed with M13K07 then grown with low shaking for 10 hours. Note the similarity to Figure 2: No polyphage structures are apparent. These cells produce single phage.


Displaying Fusion Proteins
In testing for the incorporation of our fusion into the phage coat, we chose to have M13K07 package our fusion instead of hyperphage. Testing with hyperphage would be difficult because the 100-fold reduction in infectivity (Rakonjac and Model, 1998) and the property of being tethered to the membrane introduce complications in the necessary amplification and purification steps. M13K07 and Hyperphage are equivalent in all other aspects, so M13K07 makes an ideal system for testing the ability of our fusions to be incorporated into the phage coat. We transformed cells with our fusions, infected them with the M13K07 helper phage, and purified the resulting amplified phage, then western blotted with HA and Myc antibodies. We did not induce cultures because our fusions were under control of R0065, a very leaky promoter, and we postulated that the basal level of expression would be enough for incorporation.

In the western blot, we observed signals from p8-Fos* and p8-GR1. The other linkers may require some tuning of induction or additional troubleshooting before we observe incorporation.
Figure 4   click to enlarge


Figure 4. Western Blot of p8-Linkers
Of our fusions, p8-Fos, p8-Base, and p8-GR2 are tagged with Myc, and p8-Jun, p8-Acid and p8-GR1 are tagged with HA. Purified M13K07 and M13KE were run as negative controls (neither have fusion protiens). p8-GR1 was run on the Myc blot as an additional negative control, as p8-GR1 lacks the Myc tag. In all cases, about 10^11 phage were loaded onto the gel.

*Side note: Interestingly, p8-Fos shows a band at the expected 13 kD and another band at 15kD. One speculation is that because we changed an Alanine to a Leucine at the cleavage site (the joining between the p8 leader sequence and the coil), we may have created a fusion that is cleaved at a lower efficiency. This speculation requires additional thought and research, however; it will be considered in the debugging of the other p8-linkers.

Cross-linking
Over the course of the summer, we've found that taking AFM images is difficult and time-consuming. Our original plan was to take AFM images of cross-linking hyperphage. After repeated attempts and little success, we realized that we needed to have a fast way of debugging our system.

To facilitate fast debugging, we designed a system that would couple the heterodimerization of GR1 and GR2 to a fluorescent output, via split GFP.

The animation above illustrates GR1 and GR2 binding together and allowing for the GFP to form and fluoresce. Unfortunately, we will not have time to acquire data from our split GFP system before the wiki freeze.

Conclusions and Future Directions
We've created polyphage structures and sucessfully incorporated Fos and GR1 into the phage coat. These are the first steps towards accomplishing our vision of a living biomaterial. However, our accomplishments can be used by other researchers or iGEM teams for other goals. For example, if MIT iGEM 2011 wanted to make a living filter, they could use our system to display GR1 on polyphage. GR2 could be fused with a protein that binds an organic or inorganic substance of interest, e.g. gold. One can imagine that the protein would be able to bind the substance, and attach to the polyphage via the GR1/GR2 interaction. The bacteria could then be spun down slowly, taking the substance out of the solution. This example is just one of many possible extensions of the bacteriophage portion of the "living materials" project.
← Construction       Context →

Retrieved from "http://2010.igem.org/Team:MIT_phage_results"