Design

For the measurements in vivo we decided to use an expression cassette consisting of Green Fluorescent Protein (GFP) coding sequence upstream of the switch and another fluorescent protein coding sequence downstream of it. Both protein coding sequence carry the same ribosome binding site, therefore, the GFP fluorescence can be used as internal control in measurements. Since the spectra should not overlap and to avoid FRET as well as an pure overlap of the spectra, we settled on the usage of red fluorescent protein variants, namely mRFP1 in the first try. While the GFP fluorescence is used to normalize the measurements, the RFP fluorescence is used to detect termination/antitermination.

Upon binding of the signal, the stem loop of the switch would resolve leading to red fluorescence. The GFP fluorescence as internal control carries the advantage that errors in the measurement set can be detected easily. Lack of arabinose or promoter insensitivity can be recognized as well as problems with the fluorescence measurement itself. Plus, we have a way to normalize our measurements and compare different preparations in relation to each other.

Construction and Cloning

Our measuring plasmid is based on the BioBrick pSB1A10, A1, distribution 2010. Unfortunately after two months of cloning we had to recognize that the plasmid in use did not work (see also Biobrick validation--> link). So after the first unsuccessful attempts we decided to reclone the system, substituing RFP to mCherry, a dsRED derivative with a spectra in the far red, and adding arabinose inducible promoters in front of both fluorescent proteins.

To control the expression of the switch, the particular DNA sequence itself is under the control of an IPTG dependent promoter. In the future we want our networks to be able to respond to a variety of external signals like small metabolites, ions or whatever can be found in the parts registry. For a start we went with an established and well-working system like the lac-operon. ---> PLASMID MAP
So upon induction with arabinose a rise of GFP expression can be seen. To monitor changes in gene expression we put our E. coli cells in a fluorimeter and measured fluorescent. It worked quite nicely with living cells in a fluorimeter, the only thing to avoid is too much scattering: the cell density should not exceed an OD600 of ???. Continious stirring and a set temparature at 37°C allowed measuring over severall hours. Cell density was checked in between.

Measurement

For switch evaluation, IPTG was added to the cells after about two hours after arabinose induction (baseline). ??? Stimmt das?? A rise of RFP/mCherry emission should be visible in case of a working switch.
For evaluation of the measuring plasmid itself we incorporated a positive control in every measurement. A random sequence in between GFP and RFP/mCherry was chosen in a corresponding length. An increase in both GFP and mCherry was detectable in the positive control and in the same amount after quantum yield correction, proving that the measuring plasmid is working nicely.
As a negative control we measured the same plasmids as for every switch but without signal. Since our switches are effective terminators if no signal is bound, transcription can not occur and no RFP/mCherry is produced.

When measuring the termination of our BioBricks and the antitermination by their corresponding signal-RNA, we should be able to observe an increasing RFP emission compared to the GFP emission upon induced signal-RNA production in the cells/in the kit:

With these measurements, it should also be possible to observe differences in efficiency of termination as well as antitermination between our designed switches.

Design

In this assay we used the same constructs as engineered for the in vivo studies.

Measurements

We used the cell-free E. coli S30 extract system for circular DNA provided by promega^[1], which is prepared by modification fo the Method Zubay et al. described. The characterization of the kit can be obtained from the [http://www.promega.com/catalog/catalogproducts.aspx?categoryname=productleaf_335&ckt=1 Parts Registry]. wie genau messungen, verweis auf stuff in registry.
probleme: begrenzte kapazitaet, dna menge, schwaches signal (mit/ohne vgl doof) - selbe ergebnisse (wenn uehaupt) wie in vivo

If measureable effects with our basic concept can be seen in vitro we can use the so gained data to optimize the system in vivo. Since we are working on a totally new principle of trancriptional control, we used this approach for easy variation of different variables like the length of the core unit and the switch to signal ratio. To study the switches on the transcriptional level gives the advantage, that we would have less interferences and possible artefacts. Also, we are not sure how cellular mechanisms like degradation of RNases or interacting factors as well as molecular crowding influence our systems.
Working with in vitro systems also has the advantage that an input is not needed anymore and the output can also be generated easily. We used two readouts with two different transcription systems to check and investigate our devices: First, we used an malachitegreen-binding aptamer for an fluorescent output (which will be described in detail later) and second, we simply put our reaction educts on an denaturing acrylamide-gel to check for RNA varying in length. As for two different transcription systems we used on the one hand E. coli-RNA Polymerase (RPO) based transcription since the aim is to apply our system in vivo and on the other hand T7 based transcription which is well established through literature.

T7 RNA polymerase

E. coli RNA polymerase

In comparison to the T7 RNA Polymerase the E. coli RNA Polymerase requires slightly more sophisticated proceedings when it comes to the design of switches and handling of the enzyme. The biggest in our case was to store it properly since the only -80°C fridge was in another building.
E. coli RPO was ordered saturated with σ70-factor. The switch consists of an ???-promoter, the switch itself and a ???.

Denaturing Polyacrylamide gel electrophoresis

Malachite green assay

Emission spectra of malachite green; A: without signal-RNA, B: with signal-RNA

Malachite-green is a dye with a negligible fluorescence in solution but undergoes a dramatic increase if bound by a RNA -aptamer. Upon binding to the aptamer, the fluorescence of malachite-green increases about 3000 times making it an exceptionel good marker. Since the binding is very specific, transcription in dependence of a signal can be monitored by measuring the fluorescence of malachite-green over time if the aptamer is located behind the switch. Transcription of the aptamer will only take place after anti-termination by a signal. An increase should be visible over time.

For the T7-based measurements we ordered single stranded signals for a first attempt and added matching single strands complementary to the T7 promoter region. The switch was amplified using PCR and consisted of the following elements: Primer-binding site - T7 promotor - switch - malachitegreen binding aptamer. Upon binding of a correct signal to the switch, the stem loop dissolves and transcription is possible.

OLD: A second possibility to measure parameters of our switches we came up with, was the idea to investigate our system on the transcriptional level only. Therefore, we decided to use malachite green as reporter. Malachite green in a fluorescent dye, whose emission increasing dramaticly (about 3000 times) upon binding of a specific RNA-aptamer. The RNA-aptamer

---concept to be described, as well as literature--- <ref>refs</ref>

We made constructs comprising of a sigma(70)-binding promoter followed by a short nonsense sequence, the switches and the aptamer sequence.
Also we made constructs, where the transcription of the signal-RNA is under the control of a sigma(70) promoter. These two linear DNA-constructs, together with the e.coli RNA-polymerase and the right buffer conditions should represent an easy-to-handle measurement kit on the transcriptional level.

So geht ne PCR

So geht ne PCR

So haben wir in vivo gemessen

So haben wir in vitro gemessen

So haben wir in vivo gemessen

08.04.2010

Flo & Philipp

PCR

• samples:
  • R0011_His
  • R0011_Trp
  • Control
• protocol: protocols
  • templates: purified PCR products from 5.2.2010
  • primer G1004/1005
  • polymerase: Taq
  • programm: igempcr

Purification of PCR products with QIAquick PCR purification Kit

• protocol followed. exceptions: DNA-binding/unbinding with 3min 6000rpm followed by 60sec full speed

2% Agarose Gel

• in 1x TAE.

09.04.2010

Philipp & Flo

Gel of PCR products from 08.04.2010

• loaded: 10 uL sample+2 uL 6x GLD, 4/2 uL LMW standard
• 110 V, 90min
• stained with Sybrgold, 20min, 1:10.000 dilution in TAE
• Standard - Control - R0011_His - R0011_Trp - Standard(=low molecular weight (see Protocols#Lab_Protocols))

File:100409.JPG

15.04.2010

Philipp & Flo

[http://web.e14.physik.tu-muenchen.de/igem/index.php/Protocols#PCR PCR] of B0014 and R0011

16.04.2010

Philipp & Flo

• Purification of PCR products from 15.04.2010 using QIA kit
  
  

• Concentrations measured with nanodrop:
  
  

• PCR of B0014
  
  • Purification with the Zymo Kit, Elution in 20 uL H2O
  • Concentration measured with nanodrop, 17.5 ng/uL --> worked
    
    

• Digestions of:
  
  

• Gel for purification of the cleaved plasmid
  • 2% Agarose in 1x TAE
  • 120 V, 90 min
  • stained with SybrGold
  • digestion, digestion, 1 kb ladder
    • Digestion worked (partly). band at 2000 bp (backbone) cut
      
      

File:100416.png

• Purification of DNA from Gel
  • using the Zymo Kit

• Ligation of HisSig/TrpSig with R0011in 2 reactions
  
  

* approximated from the amount used in the digestion before

19.04.2010

• PCR of R0011-TrpSig and R0011-HisSig
  
  • Purification with the Zymo Kit, Elution in 30 uL H2O
  • Concentration measured with nanodrop: c(R0011-TrpSig)=20 ng/µL, c(R0011-HisSig)=12.5 ng/µl --> worked
    
    

• Gel for analysis of ligation and PCR
  • 2% Agarose in 1x TAE
  • 110 V, 90 min
  • stained with SybrGold 1:10000 20 min
  • pure R0011 PCR product used as control

File:GEL 20100419beschriftet.png

Samples seem to have run further than the buffer/dye-Front! But: Ligation Products show bands at shorter lengths than R0011 alone --> Ligation didn't work ?!?

• Ligation of HisSig/TrpSig with R0011in 2 reactions
  
  

* approximated from the amount used in the digestion before

20.04.2010

• Gel for analysis of ligation and PCR (repeat of yesterday's gel)
  • 2% Agarose in 1x TAE
  • 130 V, 75 min
  • stained with SybrGold 1:10000 60 min
  • pure R0011 PCR product used as control
  • Excision and purification of marked bands at 200bp using QIA Kit, elution in 30 µl H2O
    

File:Gel100420marked.png

• PCR of excised and purified bands of R0011-TrpSig and R0011-HisSig
  
  • complete samples (30 µl) used as templates
  • Purification with the Zymo Kit, Elution in 30 uL H2O
  • Concentrations of PCR-products: 0.5-1 ng/µl --> Gel excision or PCR didn't work

• Transformation (Woehlke-Lab)
  • 8 µl of ligation product pSB1K3-B0014 to 50 µl XL-10 competent cells
  • 200 µl plated on a Kanamycin-containing Plate
  • remaining 800 µl stored @4°C in S1-lab

21.04.2010

• Gel for analysis of ligation and PCR (repeat of yesterday's gel)
  • 2% Agarose in 1x TAE
  • 110 V, 90 min
  • stained with SybrGold 1:10000 80 min
  • pure R0011 PCR product used as control
  • Excision and purification of marked bands at 200bp using Zymo 5 Kit, elution in 20 µl H2O
    

File:100421beschriftet.gif

• PCR of excised and purified bands of R0011-TrpSig and R0011-HisSig
  
  • complete samples (20 µl) used as templates
  • Purification with the Zymo Kit, Elution in 25 uL H2O
  • Concentrations of PCR-products:
    • R0011-TrpSig: 22.5 ng/µl
    • R0011-HisSig: 9.5 ng/µl

--> worked!!!!!

• 'Colony PCR
  • 7Colonies picked and resuspended in 20 µl LB+Kana (each)
  • PCR of 2 µl of each sample, 2 µl as negative control (Program: ColonyPCR, modified)
  • 15 µl of each sample mixed with 3 µl GLPn and loaded to Gel

File:100421colony.png

• Overnight cultures:
  • remaining 18 µl of samples 1, 3, 6, and 7 added to 5 ml LB + kanamycin
  • 37°C on Shaker

22.04.2010

• Gel for purification of PCR products R0011-TrpSig and R0011-HisSig (yesterday's result)
  • 2% Agarose in 1x TAE
  • 110 V, 90 min
  • stained with SybrGold 1:10000 30 min
  • pure R0011 PCR product used as control
  • Excision and purification of marked bands at 200bp using Zymo 5 Kit, elution in 20 µl H2O
    

File:100422beschriftet.png

• Miniprep
  • Result: about 4 µg Plasmid

23.04.2010

• Digestion of:
  
  

Incubated 90 min @ 37°C

• Gel for purification of the cleaved plasmid
  • 2% Agarose in 1x TAE (leftover from yesterday)
  • 140 V, 90 min
  • stained with SybrGold 40 min
  • 4 µl 1 kb ladder, 10 µl purified digestion + 2 µl GLPn, 10 µl purified digestion + 2 µl GLPn
    • Digestion worked (partly). band at 2400 bp cut out
      
      

File:100423beschriftet.png

• Purification of DNA from Gel
  • using the Zymo Kit
  • elution in 25 µl H2O
• A260/A230 and A260/A280 values were strange (see labbook)

26.04.2010

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.

This is what we did in week xxx.