"
Team:Cambridge/Gibson/Protocol
From 2010.igem.org
(→Step 3: PCR) |
(→Step 3: PCR) |
||
| (5 intermediate revisions not shown) | |||
| Line 18: | Line 18: | ||
==Step 3: PCR == | ==Step 3: PCR == | ||
| - | PCR is a bit of a dark art, but we have found that these general principles have served us well over the summer | + | PCR is a bit of a dark art, but we have found that these general principles have served us well over the summer: |
| + | <div style="float:right; clear:both"> </div> | ||
| + | {{:Team:Cambridge/Templates/RightImage|image=Phusion.jpg|caption=Phusion Polymerase}} | ||
<html> | <html> | ||
<style> | <style> | ||
| Line 77: | Line 79: | ||
</div> | </div> | ||
</html> | </html> | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
The Annealing T<sub>m</sub> that should be used is the temperature of the main 20 or so bases of the primer (not including the flap), since the flap only begins to anneal after the first few cycles, by which point primer specificity is less of an issue. | The Annealing T<sub>m</sub> that should be used is the temperature of the main 20 or so bases of the primer (not including the flap), since the flap only begins to anneal after the first few cycles, by which point primer specificity is less of an issue. | ||
| Line 99: | Line 94: | ||
<i>e.g. If you were ligating two fragments (A and B) you could put:</i> | <i>e.g. If you were ligating two fragments (A and B) you could put:</i> | ||
| - | |||
| - | |||
<html> | <html> | ||
<style> | <style> | ||
| Line 106: | Line 99: | ||
table.vistable{border-left:1px solid gray; border-bottom:1px solid gray;} | table.vistable{border-left:1px solid gray; border-bottom:1px solid gray;} | ||
</style> | </style> | ||
| - | <div align=" | + | <div align="left"> |
<table class="vistable" padding="0" cellspacing="0"> | <table class="vistable" padding="0" cellspacing="0"> | ||
<tr> | <tr> | ||
Latest revision as of 20:31, 26 October 2010
The original paper in nature describing Gibson Assembly can be found [http://www.nature.com/nmeth/journal/v6/n5/full/nmeth.1318.html here].
Step 1: Design Primers
If you wish to ligate two pieces of DNA using Gibson they must be altered so as to have 40bp of overlap at the point of ligation.
The standard way to do this is with PCR with specialised primers (see mechanism). We have designed a tool to help you do this: [http://www.gibthon.org Gibthon]
Step 2: Order Primers
This step can take a while, so Gibson Assembly requires some planning ahead
Step 3: PCR
PCR is a bit of a dark art, but we have found that these general principles have served us well over the summer:
| Step | Temp | Time |
| 1:Initial Melting | 98°C | 30s |
| 2:Melting | 98°C | 10s |
| 3:Annealing | Tm°C | 15s |
| 4:Elongation | 72 | 45s per kb DNA |
| 5:GoTo step 2 | 30 times | |
| 6:Final Elongation | 72°C | 7m30 |
| 7:Final Hold | 4°C | ∞ |
The Annealing Tm that should be used is the temperature of the main 20 or so bases of the primer (not including the flap), since the flap only begins to anneal after the first few cycles, by which point primer specificity is less of an issue.
The Polymerase mixture we used was [http://www.finnzymes.com/pcr/phusion_high_fidelity_pcr_mastermix.html 2x Phusion MasterMix].
Step 4: Gibson Assembly
1) Prepare Gibson Master Mix
2) Add DNA to be ligated and Master Mix in volumetric ratio 1:3
3) Incubate for 1 hour at 50°C
e.g. If you were ligating two fragments (A and B) you could put:
| 2.5µl | fragment A |
| 2.5µl | fragment B |
| 15µl | Gibson Master Mix |
Step 5: Transformation
The reaction mixture generated above should contain enough DNA to directly transform cells, although this is of course limited by the amount of DNA in the tube before the ligation.
