Team:TU Munich/Lab

From 2010.igem.org

Revision as of 16:24, 11 October 2010 by Cui (Talk | contribs)

Navigation:

Home →  Lab

iGEM MainPage

Contents

Experiment Design

In vivo Measurements

Read more

Our initial idea to prove our concept of antitermination was to use flourescent proteins as reporters. This approach gives the opportunity to measure the termination and antitermination efficiency of our designed BioBricks in vivo as well as in vitro, the latter using a translation kit based on E. coli lysate.


In principle we decided to use Green Fluorescent Protein (GFP) as an internal control in front of the switch and another fluorescent protein right after the switch. Since the spectra should not overlap and to avoid FRET as well as an pure overlap of the spectra, we settled on the usage of red fluorescent proteins, namely RFP itself, in the first try. We would use GFP fluorescence as internal control and RFP fluorescence as signal to detect termination/antitermination by our switch we cloned in between the coding sequences of the proteins. Upon binding of the signal the stem loop of the switch would resolve leading to red fluorescent additional to the green one of GFP. The internal control carries the advantage that errors in the measurement set can be detected easily. Lack of arabinose or promotor insensitivity can be recognized as well as problems with the fluorescence measurement itself. Plus, we have a way to normalize our measurements and compare different preparations in relation to each other.
Our measuring plasmid is based on the BioBrick ??, A1, distribution 2010. Unfortunately after two months of cloning we had to recognize that the plasmid in use did not work (see also Biobrick validation--> link). So after the first unsuccessful attempts we had to reclone the system, substituing RFP to mCherry, a dsRED derivative with a spectra in the far red, and adding arabinose inducible promoters in front of both fluorescent proteins.


our idea


To control the expression of the switch, the particular DNA sequence itself is under the control of an IPTG dependent promotor. In the future we want our networks to be able to respond to a variety of external signals like small metabolites, ions or whatever can be found in the parts registry. For a start we went with an established and well-working system like the lac-operon.
So upon induction with arabinose a rise of GFP expression can be seen. To monitor changes in gene expression we put our E. coli cells in a fluorimeter and measured fluorescent. It worked quite nicely with living cells in a fluorimeter, the only thing to avoid is too much scattering: the cell density should not exceed an OD600 of ???. Continious stirring and a set temparature at 37°C allowed measuring over severall hours. Cell density was checked in between.


For switch evaluation, IPTG was added to the cells after about two hours after arabinose induction (baseline). ??? Stimmt das?? A rise of RFP/mCherry emission should be visible in case of a working switch.
For evaluation of the measuring plasmid itself we incorporated a positive control in every measurement. A random sequence in between GFP and RFP/mCherry was chosen in a corresponding length. An increase in both GFP and mCherry was detectable in the positive control and in the same amount after quantum yield correction, proving that the measuring plasmid is working nicely.
As a negative control ???

When measuring the termination of our BioBricks and the antitermination by their corresponding signal-RNA, we should be able to observe an increasing RFP emission compared to the GFP emission upon induced signal-RNA production in the cells/in the kit:

our idea

Wiith these measurements, it should also be possible to observe differences in efficiency of termination as well as antitermination between our designed switches.

Close

In vitro Measurements

Read more

A second possibility to measure parameters of our switches we came up with, was the idea to investigate our system on the transcriptional level only. Therefore, we decided to use malachite green as reporter. Malachite green in a fluorescent dye, whose emission increasing dramaticly (about 3000 times) upon binding of a specific RNA-aptamer.

our idea

---concept to be described, as well as literature--- <ref>refs</ref>

Emission spectra of malachite green; A: without signal-RNA, B: with signal-RNA

To study the switches on the transcriptional level gives the advantage, that we would have less interferences and possible artefacts. Also, we are not sure how cellular mechanisms like degradation of RNases or interacting factors as well as molecular crowding influence our systems.

We made constructs comprising of a sigma(70)-binding promoter followed by a short nonsense sequence, the switches and the aptamer sequence.
Also we made constructs, where the transcription of the signal-RNA is under the control of a sigma(70) promoter. These two linear DNA-constructs, together with the e.coli RNA-polymerase and the right buffer conditions should represent an easy-to-handle measurement kit on the transcriptional level.









Close

In vitro Translation

Read more

So haben wir in vivo translation gemessen

Close


Protocols

Molecular Biology

PCR

Read more

So geht ne PCR

Close

Digestion

Read more

So geht ne PCR

Close

In vivo measurement

Read more

So haben wir in vivo gemessen

Close

In vitro measurement

Read more

So haben wir in vitro gemessen

Close


Lab Book

Explanation:

Cloning [REDBOX]
In vivo measurement [BLUEBOX] => LINK: In vivo Hauptseite
In vitro malachite measurement [GREENBOX] => LINK: In vitro malachite Hauptseite
In vitro translation kit [YELLOWBOX] => LINK: In vitro translation kit


Week1 [REDBOX]
Week2 [REDBOX] [BLUEBOX]
Week3 [REDBOX]