Team:Kyoto/LearnMore

Lysis Cassette

Sam7 Mutation

RPU (Relative Promoter Unit)

Though BioBrick parts are standardized in terms of how individual parts are physically assembled into multi-component systems, many of them are not standardized in the point of characterization.

Unfortunately, it is known that the absolute activity of BioBrick promoters varies across experimental conditions and measurement instruments [1]. However, Kelly et al found that this variation could be reduced by measuring the activity of promoters relative to <partinfo>J23101</partinfo> which is a promoter as an in vivo reference standard for promoter activity by ~50%. They defined a Relative Promoter Units (RPU) in order to report promoter characterization data in compatible units. In order to measure RPUs of promoters, the synthesis rate of Green Fluorescent Protein (GFP) encoded by mRNA transcribed from each promoter is observed.

RPU is defined by Equation 1: Relative activity of promoter φ RPUs=PoPSSSφPoPSSSJ23101 (1)

PoPS (Polymerase Per Second) is the unit of absolute “promoter activity”, and “promoter activity” is defined as the number of RNA polymerase molecules that pass by the final base pair of the promoter and continue along DNA as an elongation complex. PoPSSS is PoPS at the steady state of following system(d[M]/dt=0, d[I]/dt=0, d[G]/dt=0:

d[M]dt=n*PoPS-γM[M] (2)

d[I]dt=ρM-(a+γI)[I] (3)

d[G]dt=aI-γG[G] (4)

Where

[M] is the concentration of mRNA,

[I] is the concentration of immature GFP,

[G] is the concentration of mature GFP,

γM is the mRNA degradation rate,

a is the GFP maturation rate,

γI is the degradation rate of immature GFP

n is the copy number of the plasmid containing the promoter

ρ is the rate of synthesis of immature GFP in absolute units of protein per second per mRNA.

By combining equation 2, 3, 4 and 5 at the steady state, equation 6 and 7 are obtained:

Scell=aI (5)

Here Scell is define as the per cell mature GFP synthesis term.

PoPSSS=γM(a+γI)ScellSSρan (6)

PoPSSS=γM(a+γI)γGGcellSSρan (7)

Here Gcell is define as the per cell mature GFP synthesis term.

From equation1 and 6 RPU is described as equation8.

RPU=γM,φaφ+γI,φScell,φSSρφaφnφγM,J23101aJ23101+γI,J23101Scell,J23101SSρJ23101aJ23101nJ23101 (9)

If the test promoter φ and the reference standard promoter are measured under the same culture conditions and both promoters are carried on the same backbone plasmid, following equations are approved.

aφ=aJ23101=a (10)

nφ=nJ23101=n (11)

γM,φ=γM,J23101=γM (12)

ρφ=ρJ23101=ρ (13)

From equation 9, 10, 11, 12 and 13, Equation 14 is accomplished.

RPU=a+γI,φScell,φSSa+γI,J23101Scell,J23101SS (14)

In addition, immature GFP is stable so that protein degradation is negligible compared to dilution due to cell growth (γI,φ=μφ and γI,J23101=μJ23101, where μis the cellular growth rate). Therefore, equation 14 can be modified to equation 15:

RPU=a+μφScell,φSSa+μJ23101Scell,J23101SS (15)

And if the growth rates of both strains are almost same, equation 16 is approved.

if |μ_φ-μ_J23101 |≪a ,(a+μφ)(a+μJ23101)≈1 (16)

Accordingly, we can make equation 17 from eqution16.

RPU=Scell,φSSScell,J23101SS (17)

ScellSS can be described by equation18:

ScellSS=(dF/dt)/ABS (18)

Therefore, RPU is described by equation 19:

RPU=(dFφ/dt)/ABSφ(dFJ23101/dt)/ABSJ23101 (19)

We can also establish equation20 from equation1, 6, 10, 11, 12 and 13.

RPU=[G]cell,φ[G]cell,J23101*μφμJ23101 (20)

RPU can be calculated from equation19 or equation20. Therefore, we have to observe GFP synthesis rate and ABS (OD600) of both strains or to measure GFP concentration per cell and growth rate of both strains to measure RPU.

To see how to measure RPU practically, go protocol.

To see more about RPU, go reference.

Reference [http://www.ncbi.nlm.nih.gov/pubmed/19298678 PMID: 19298678] Kelly JR, Rubin AJ, Davis JH, Ajo-Franklin CM, Cumbers J, Czar MJ, de Mora K, Glieberman AL, Monie DD, Endy D., Measuring the activity of BioBrick promoters using an in vivo reference standard., J Biol Eng. 2009 Mar 20;3:4.