Team:UCL London/Characterisation

From 2010.igem.org

Revision as of 03:51, 28 October 2010 by Zcbee12 (Talk | contribs)

UCL IGEM 2010

RETURN TO IGEM 2010

1. CHARACTERISATION OF NEW PARTS

Our pTAC with RFP[http://partsregistry.org/wiki/index.php?title=Part:BBa_K301001 BBa_K301001] reporter was characterised at lab scale by carrying out a successful transformation with a control.

Ucl-Part-BBa-K301001.png


 


IPTG induction of the reporter device BBa_K301001 was demonstrated in a lacI host strain with 0.1mM IPTG (panel B). A lac promoter device was tested as positive control (panel C).

As predicted, IPTG induction was not observed when our new device resided in a lacI negative host strain (panel A) or when the pTac biobrick was omitted (panel D).


The following is the manual for the construction of [http://partsregistry.org/wiki/index.php?title=Part:BBa_K301000 BBa_K301000]

Check out our parts page to see the parts submitted in more detail [http://partsregistry.org/cgi/partsdb/pgroup.cgi?pgroup=iGEM2010&group=UCL_London&Done=1|UCL_London 2010 iGEM Team Parts].


2. CHARACTERISATION OF EXISTING PARTS/DEVICES AT 1 L FERMENTER SCALE

As part of the Gold criteria which is our target, we had to characterise an existing part, and so we decided to characterise 3 devices from our 2009 parts;

Fermenter 1 - [http://partsregistry.org/wiki/index.php?title=Part:BBa_K239011 UCL_London 2009 iGEM BBa_K239011 PART]

Stress Light GFP Anaerobic Metabolism Detector: mNARK promoter 
UCL-CHARAC11-1.png
UCL-CHARAC11-2.png





 

By analysing the above data, it can clearly be shown that the cells are growing well as they are making use of the oxygen which remains at relatively low levels on A. B indicates their succesful growth showing OD values gradually increasing up to a peak of around 175, although the time taken to do so is approxiamtely double that of normal processes, and this can be attributed to the introduction of new parts into the E.coli genome resulting in some sort of interaction, that's our theory!

Graph C once again confirms our characterisation as it shows the AU of the green fluorescent dye produced increasing with time. D & E show how the circuit reacts to changes in oxygen at certain intervals where we cut the oxygen of to observe the circuits reaction.

Fermenter 2 -[http://partsregistry.org/wiki/index.php?title=Part:BBa_K239009 UCL_London 2009 iGEM BBa_K239009 PART]

GFP test devise for Spy promoter

UCL-CHARAC9.png ...



 

Fermenter 3 - [http://partsregistry.org/wiki/index.php?title=Part:BBa_K239015UCL_London 2009 iGEM BBa_K239015 PART]

GFP test devise for Deg P promoter
UCL-CHARAC15.png




 

Once again, all 3 graphs show successful characterisation results as the green dye AU is at relatively high levels and the oxygen in A as stated previously is low towards the end of the cycle indicating efficient use of oxygen by the cells.

Images from fermentation chamber

MNARK Infors 05.jpg
MNARK Infors 02.jpg


 

The image on the left is that of the control, while that on the right showing the characeterised mNark promoter fluorescent green.

The following video shows the moment of that our iGEM aspirations came true, and we saw green fluorescence;


From the paste removed from the fermenter vessel following the successful characterisation of the parts, we used it to creatively mark the words UCL iGEM in plates and hence further emphasizing the results that the parts do work.

UCL-MNARK paste.jpg
 


MNARK IGEM plus control 02.jpg
MNARK IGEM plus control 03.jpg
 

These images further conclude that we succesfully characterised our mNark Promoter as both images have both a control with no observed dye and one showing the green dye, with which we crafted the words UCL and iGEM as shown above.

3. Charactisation of Cambridge Part:BBa_K274003

K274003 Diagnostic Gel .jpg

E. coli turned dark green after transformation of this plasmid. This is unexpected as there is no promoter upstream of the operon.

Diagnostic DNA gel was run to test all 4 restriction sites. BBa_K274003 was cut with XbaI, PstI, EcoRI & SpeI, XbaI & PstI. A gel picture is shown as below.

This plasmid did not cut with Xba I restriction site in our hands. As such we could not use it to assemble after other parts.

Click on the following link for the [http://partsregistry.org/Part:BBa_K274003:Experience#User_Reviews Cambridge Part Review]

 



 

Retrieved from "http://2010.igem.org/Team:UCL_London/Characterisation"