Team:Michigan/Media Recipes
From 2010.igem.org
- Home
- Team
- Project
- Parts
- Modeling
- Notebooks
- Safety
-
Media Recipes
General Recipes
LB media
- 10 g LB medium
- 500 mL DI water
autoclave to sterilize
LB media with agar
- 10 g LB medium
- 7.5 g agar
- 500 mL DI water
autoclave to sterilize
add antibiotics after autoclaving when warm to touch (about 50°C)
pour plates when warm to the touch (about 50°C)
0.1 M CaCl2 solution
- 0.735 g of CaCl2*2 H20
- 50 mL of DI water
filter sterilize
1.0 M CaCl2 solution
- 7.35 g of CaCl2*2 H20
- 50 mL of DI water
filter sterilize
1.0 M MgSO4
- 12.323 g of MgSO4*7 H20
- 50 mL of DI water
filter sterilize
Ampicillin Antibiotic Stock Solution (100 mg/mL)
- 1 g of ampicillin
- 5 mL of DI water
- 5 mL of ethanol
filter sterilize and make 1 mL aliquotes to store in the -20°C freezer
Kanamycin Antibiotic Stock Solution (50 mg/mL)
- 250 mg of kanamycin
- 5 mL of DI water
filter sterilize and make 1 mL aliquots to store in the -20°C freezer
Tetracycline Antibiotic Stock Solution (50 mg/mL)
- 250 mg of tetracycline
- 2.5 mL of DI water
- 2.5 mL of ethanol
filter sterilize and make 1 mL aliquots to store in the -20°C freezer
IPTG stock solution (1 M)
- 0.25 g of IPTG
- 1049 uL of DI water
filter sterilize with .22 um filter
40% glucose solution
- 20 g of glucose
- 50 mL of DI water
filter sterilize
0.1 M NaOH solution
BE VERY CAREFUL WHEN MIXING! SOLID NaOH BURNS YOUR SKIN BUT YOU MAY NOT FEEL IT AT FIRST! MAKE SURE ANY SPILLS ARE CLEANED UP VERY WELL!
- 0.2 g of NaOH
- 50 mL of sterile water
Filter Sterilize
10mM dNTP mix for PCR
MAKE SURE ALL REAGENTS ARE WELL MIXED BEFORE STARTING BY PULSE CENTRIFUGING OR FLICKING
- 100 uL of 100mM dATP
- 100 uL of 100mM dTTP
- 100 uL of 100mM dGTP
- 100 uL of 100mM dCTP
- 600 uL of ultra pure water
aliquot into 50 uL volumes (this will take 20 1.5mL eppendorf tubes)
Oil Sands Recipes
1.5 mg/mL Cyclohexanecarboxylic acid solution
Cyclohexanecarboxylic acid is volatile and should only be used under a hood. For accurate measurement, use a covered scale with sliding doors (in the hood). Store in the corrosive cabinet.
- 0.075 g cyclohexanecarboxylic acid
- 50 mL of DI water
filter sterilize
Bushnell-Haas Salts (w/out carbon source)
- 0.4 g of KH2PO4
- 0.4 g of K2HPO4
- 0.4 g of (NH4)2 SO4 or NH4NO3
- 0.002 g of FeCl3
- 318 mL of DI H2O
Autoclave at 15 psi and 121°C for 30 minutes
After the media has cooled completely add:
- 665 uL of 1 M MgSO4 solution
- 72 uL of 1 M CaCl2 solution
Bushnell-Haas Media with glucose
- 39.75 mL of Bushnell-Haas Salts
- 2 mL of 40% glucose solution
- 8.25 mL of sterile DI water
Bushnell-Haas Media with cyclohexanecarboxylic acid
- 39.75 mL of Bushnell-Haas Salts
- 4 mL of cyclohexanecarboxylic acid solution
- 6.25 mL of sterile DI water
20 mg/mL Casamino Acid Solution
- 0.18 g Casamino acid
- 9 mL of DI water
Filter sterilize
Bushnell-Haas Media with glucose and casamino acids
- 39.75 mL of Bushnell-Haas Salts
- 2 mL of 40% glucose solution
- 2 mL of sterile DI water
- 6.25 mL of casamino acid solution
Bushnell-Haas Media with cyclohexanecarboxylic acid adjusted to pH of 9
- 39.75 mL of Bushnell-Haas Salts
- 4 mL of cyclohexanecarboxylic acid solution
- 6.25 mL of sterile DI water
Test how much 0.1 M NaOH must be added to 1 mL of media to raise it to a pH of 9 (add 1 uL of base at a time)
Scale up the amount of 0.1 M NaOH solution to add to the remaining volume of media (approaching final amount slowly)
On 8/3/2010, approximately 20 uL of 0.1 M NaOH had to be added to 1 mL to get to a pH between 8 and 9 (tested with pH paper) and 675 uL of 0.1 M NaOH was added into the 45 mL of remaining media.
Retrieved from "http://2010.igem.org/Team:Michigan/Media_Recipes"