Wet Lab>Temperature Control

Outline


    Temperature control device was constructed in our Mosquito Intelligent Terminator. The thermosensing function is controlled by the 37°C induced RBS (BBa_K115002) and the tetR gene(BBa_C0040). By using different temperature-regulated ribosome binding sites, we can modify the switching temperature (37°C ) of this device according to different needs.

    Since the tetR gene can repress the pTet promoter (BBa_R0040), the downstream genes of pTet, such as the cry gene and the GFP gene(BBa_E0040), can also be repressed. While the switching temperature is achieved in the incubator, pTet as well as its downstream genes will be switched off. In this condition, almost none of the green fluorescent protein and crystal protein can be detected. However, pTet and its downstream genes will not be switched off below the switching temperature. In other words, we can observe a great amount of the crystal protein as well as the green fluorescent protein only in sub 37°C environment.

 Image description

Top

Procedures

Flow Cytometry Methods

(I) Transformation of BBa_ K332032 into E. coli EPI300

  1. Thaw EPI300 E. coli cells and BBa_ K332032 plasmid on ice.
  2. Transfer 1μL of plasmid and 100μL of cells to a pre-chilled microcentrifuge tube.
  3. Incubate on ice for 5 minutes.
  4. Transfer the tubes to 42°C for 1 minute.
  5. Transfer the tubes back to ice and cool for 5 minutes.
  6. Add 200μL lysogeny broth to each tube.
  7. Recover the cells by incubating at 37°C for 30 minutes.
  8. Plate the cells on the appropriate media and antibiotic, such as agar plates with 25 µg/ml kanamycin.
  9. Incubate the cultures at 37°C overnight.

(II) Preparation of M9 minimal media

  1. Dissolve 1.695g Na2HPO4, 0.75 g KH2PO4, 0.125g NaCl, 0.25 g NH4Cl and 0.5 g Casamino acid in 250 mL double distilled water (ddH2O).
  2. Sterilize the solution at 121°C for 30 minutes by using moist heat sterilization method.

(III) Flow cytometry

  1. Pick one single colony off the transformation plate of E. coli EPI300. Dilute the bacteria with 20μL ddH2O.
  2. Add 4μL diluted bacteria into 4mL M9 minimal media supplemented with 0.2% casamino acids, 1 mM MgSO4, 2 μM thiamine, 10 mM glucose, and 50ng/ml Kanamycin. (For all of the measurements, cells were grown in M9 minimal media supplemented with 0.2% casamino acids, 1 mM MgSO4, 2 μM thiamine, 10 mM glucose, and 50 ng/ml Kanamycin antibiotic.)
  3. Incubate at 37°C overnight on a shaker at 200 rpm.
  4. Prepare 4 tubes, since we will culture these samples at 4 different temperatures. To each tube, add 4μL of the above-mentioned culture into 4mL fresh M9 media supplemented with 0.2% casamino acids, 1 mM MgSO4, 2 μM thiamine, 10 mM glucose, and 50 ng/ml Kanamycin.
  5. Incubate the tubes at 37°C with shaking at 200 rpm until an optical density of 0.1 is reached.
  6. Transfer the tubes to their corresponding temperatures, including 25°C, 30°C, 37°C, and 40°C. Use flow cytometry to measure the fluorescence and observe the changing patterns for more than 7 hours.

Top

Result

 

Above 37°

Below 37°

Bacterial growth rate

Accelerated

Slowed

RBS K115002 (37 °C induced)

Activated

Inactivated

tetR

Activated

Inactivated

pTet(inhibited by tetR)

Inhibited

Not inhibited

GFP (or cry gene)

Inhibited

Not inhibited


  We want to utilize a temperature-regulated mechanism to control the expression period of a crystal protein. Therefore, we took advantage of the interaction between 37° C induced RBS, tetR gene and pTet promoter to create the temperature regulating circuit. The following is a description of our prescribed strategy. First, we use the constitutive promoter, 37° C induced RBS (K115002), the tetR gene and terminators. We will call this part the "Regulator"(Figure1).

Image description

   Second, we combine pTet Promoter, RBS B0034, the crystal protein gene and terminators. We call this part the "Production"(Figure2)

Image description

  We use the "Regulator"> to maintain a stable growth rate of bacteria while inhibiting crystal protein protection by way of the tetR gene. Bacteria growth, particularly vector mutation rate and growth rate, is highly dependent on amplification conditions, thus crystal protein production is off during the incubation/amplification step. Because the tetR gene of the "Regulator" can block the pTet promoter of "Production", we achieve a self-regulating, temperature dependent system that monitors both bacteria growth and protein production. We speculate that when the "Regulator" and "Production" sections are combined, we can achieve a high bacteria growth rate and close to no crystal protein producing rate at T>37° C, and low bacteria growth rate and high crystal protein producing rate at T<37° C.(Figure3)

Image description

  To test the efficiency of the temperature induced RBS and the interaction between tetR gene and ptet promoter, we replaced the crystal protein gene with GFP (green fluorescence protein) gene. In this scenario, GFP will simulate the crystal protein's production, as it is easily detected by flow cytometry.(See Cytometry figure)

 Image description

   To conclude, we have verified that our strategy works. Figure 4 demonstrates the regulation of GFP in a temperature dependent fashion, as it is evident the mean GFP values are significantly lower at T>37° C. We expect our circuit design to allow steady bacteria growth and inhibit crystal protein at T>37° C, and high protein production and low bacteria growth rate at T<37° C

 

Top