"
Team:Newcastle/19 August 2010
From 2010.igem.org
(→Aims) |
|||
| Line 7: | Line 7: | ||
===Aims=== | ===Aims=== | ||
| - | To | + | To purify the products of ''yneA'', pGFPrrnB and PSB1AT3 from the gel after running gel electrophoresis. Concentration of the DNA and vectors are also checked with nanodrop. |
===Materials and Protocol=== | ===Materials and Protocol=== | ||
Revision as of 09:59, 25 August 2010
| |||||||||||||
| |||||||||||||
Contents |
yneA
Gel extraction
Aims
To purify the products of yneA, pGFPrrnB and PSB1AT3 from the gel after running gel electrophoresis. Concentration of the DNA and vectors are also checked with nanodrop.
Materials and Protocol
Please refer to gel electrophoresis, gel extraction, nanodrop spectrophotometer.
Results
| yneA 1 | yneA 2 | yneA 3 | pSB1C3 | pGFPrrnB | |
|---|---|---|---|---|---|
| Concentration of DNA ng/µl | 3.4 | 4.7 | 5.4 | 2.2 | 18.5 |
Discussion
The bands we extracted from the gel was good for pGFPrrnB, but not so strong for yneA and PSB1C3.
The results we got from the nanodrop were not as good as expected for yneA and PSB1C3.
Conclusion
We will proceed with digestion, but another set of ligation will be set up to repeat the process again.
Ligation
Aims
To ligate yneA into both vectors pGFPrrnB and pSB1C3.
Materials and Protocol
Please refer to ligation.
Ligation mix for pSB1C3 with yneA
The concentration of pSB1C3 and yneA that we got from the gel extraction earlier today was very low, so we used a different mixture set up for ligation.
Ligation mix:
| Reagents | 1:3(μl) | 1:5(μl) | Vector(μl) |
|---|---|---|---|
| Vector | 3 | 2 | 1.5 |
| Insert | 3 | 6 | 7.5 |
| 10X BUFFER | 1 | 1 | 1.1 |
| T4 Ligase | 1 | 1 | 1 |
| H2O | 2 | 0 | 0 |
| Total Volume | 10.0 | 10.0 | 10.0 |
Results and Conclusion
Please refer to 20.08.10.
Digestion
Aim
To repeat digestion from 18.08.10.
Materials and Protocol
Please refer to restriction digest.
Setting up Overnight Cultures
Aims
To prepare cultures for miniprep of yneA, pGFPrrnB and pSB1C3 tomorrow.
Materials and Protocol
Please refer to growing an overnight culture.
Subtilin Immunity
Aims
Today we received the four new primers that we ordered:
- Prom_For
- pSB1C3_for
- pSB1C3_rev
- Term_rev
These primers were ordered as a solution to the problem we encountered before we were about to attempt carry out the Gibson protocol for the Subtilin Immunity (and RocF) BioBrick. The primers will be used with previously rehydrated primers to try and obtain all four parts that we need to make the Subtilin Immunity BioBrick using the Gibson Protocol. So far the spaIFEG coding sequence (part 3) has already been successfully obtained. We still need to obtain the plasmid vector (part 1), promoter & RBS (part 2) and double terminator (part 4). So in order to do this the primers received today will be rehydrated and Phusion PCR will be carried out for each of the parts in order to amplify these parts.
Materials and protocol
Please refer to DNA rehydration page for the protocol for the rehydration of the four primers and to the Phusion PCR page for protocol followed for Phusion PCR. Table # below shows the different fragments, primers and conditions used for each tube.
| Tube | Part to be amplified | DNA fragment consisting the part | Forward primer | Reverse Primer | Melting Temperature (Tm in °C) | Size of the fragment (in bp) | Extension time* (in seconds) |
|---|---|---|---|---|---|---|---|
| 1 | Plasmid Vector | pSB1C3 | pSB1C3_for | pSB1C3_rev | 68 | 2046 + | 70 |
| 2 | Promoter and RBS (pVeg-SpoVG) | BioBrick Bba_K143053 | Prom_for | P2P2_rev | 67 | 139 + | 15 |
| 4 | Double terminator | pSB1AK3 consisting BBa_B0014 | P1T1_for | Term_rev | 63 | 116 + | 15 |
Table #: This table shows the three different Phusion PCR reactions that were carried out today. If this is successful, these three parts (part 1, 2 and 4) along with (part 3) which is already obtained can be ligated together for the construction of subtilin immunity BioBrick with the help of Gibson Cloning method.
- The extension rate of the Phusion polymerase is 1 Kb/ 30 seconds. Thus the extension time of each and every PCR reaction is slightly different.
- The primers in bold are the new primers we received today. The primers not in bold were previously re-hydrated.
Discussion and Conclusion
Tommorrow we will carry out a test gel to check the sizes of the amplified fragments and if the sizes are correct then gel extraction will be performed
rocF BioBrick
Gel extraction of linearised pSB1C3
PCR of pSB1C3, pspac oid and double terminator with new primers
Go back to our main Lab book page
   
|
    
|
