From 2010.igem.org

(Difference between revisions)

Revision as of 01:12, 3 August 2010

	Sunday	Monday	Tuesday	Wednesday	Thursday	Friday	Saturday
Week 1	-	-	-	-	-	-	-
Week 2	-	-	-	7/7/2010	7/8/2010	-	-
Week 3	-	-	-	-	-	-	-
Week 4	7/17/2010	7/19/2010	-	7/21/2010	7/22/2010	7/23/2010	-
Week 5	7/25/2010	7/26/2010	-	-	-	-	-

Quorum Sensing Team

Members include Alex Pyden, Marcus Lehr, Jennifer Hong, Eric Raynal, Katie Miskovich, and Audra Williams

7/7/10

Jennifer and Alex - in Lin Lab

Made CaCl₂ stock solution: 0.1M - 50mL

molar mass = 111 g/mol
(0.1 mol/L)(.05 L)(111 g/mol) = 555mg
dissolved 555 mg CaCl₂ in 50mL DIwater
vacuum filtered into 50mL tube

Made ampicillin stock solution:

 -1 g ampicillin
 -5mL DIwater
 -ethanol

filtered by syringe into 15mL tube
put into ten 1mL alliquots in 1.5mL tubes
stored in -20°C in ERB lab

Inoculated E. coli DH5α from frozen stock into 12 mL LB broth

put in 30°C, 200 rpm shaking, overnight

~1.5 hrs

7/8/10

Alex, Jennifer and Eric - in ERB

Made LB agar plates w/ ampicillin

 -10 g LB broth
 -7.5 g agar
 -500 mL DI water

autoclaved mixture at 121°C for 30 min (sterilize time), following Mike Nelson's protocol

Created protocols for Obtaining Deionized Water in the ERB and ERB Spectrophotometer

uploaded to Team:Michigan/Protocols section

poured 20 LB-amp plates (large)

left to solidify in ERB 1230
12 plates were used by Ann for biobrick transformations
8 plates were stored in 4°C ERB

~3.5 hrs work

Ann, Marc, Audra and Katie - in Lin Lab

Performed biobrick transformations using heat shock

Followed protocol for Transformation-heat shock
protocol located under DNA Manipulation in Team:Michigan/Protocols section

After second washing:

ODs for sample 1 and 2 were 0.378 and 0.358 respectively

4 hrs of work

7/17/10

Alex & Jennifer - in ERB

Yesterday, Marcus stored newly obtained strains in 4°C in ERB

W3110 w/ plasmids pTC6 & pET-GFP
- AI-2 reporter (E. coli, amp and kan-resistant)
MDAI2 w/ plasmids pCT6 & pET-GFP
- AI-2 reporter & LuxS null mutant (E. coli, does not produce AI-2, amp and kan-resistant)

Removed these strains from 4°C -- they are stored in soft agar stab cultures Made one streak plate on LB+amp for each strain from stabs

placed in 374°C (rm. 1239)

Made one 2mL LB+amp broth cultures in a 15mL tube for each strain from stabs

placed in 30°C, 200 rpm shaking (rm. 1230)

Placed agar stabs and LB+amp broth in 4°C

~1.5 hrs work

Created protocol/plan for experiment. Testing AI-2 Response

7/19/10

Alex and Marcus

7/17 plates are no good -- they needed kanamycin

plates were discarded
broth cultures had kanamycin added a day later -- too late to be cryostored, but they were transfered to ERB 4°C

Made LB agar

-20 g powder/500 mL DI water

autoclaved 30 min (sterilize time) 255°C
poured 4 LB plates
poured 6 LB+amp plates (100 μg/mL ampicillin)
poured 10 LB+amp+kan plates (50 μg/mL kanamycin)
all plates left to cool in ERB 1230

Obtained a rotor for 1.5mL tubes for the centrifuge from Rodger Pinto

placed in centrifuge in cold room ERB 1224

Obtained LuxS (strain JW2662-1) & MarC (for Jeremy Minty) null mutant E. coli strains from [http://cgsc.biology.yale.edu/ CGSC]

retrieved from Lin 4°C
made one spread plate on LB for each strain following Culturing CGSC Strains protocol
placed both plates in ERB 37°C

Transfered iGEM cryobox from Lin Lab -20°C to ERB -20°C

~6 hrs

7/21/10

Alex, Eric and Jeremy

{Yesterday, Marcus made broths for E. coli JW2662-1 (LuxS^-) (from spread plate), E. coli JW1522-1 (MarC^- for Jeremy Minty) (from spread plate), E. coli W3110 (from stab), E. coli MDAI2 (from stab), P. putida for Oil Sands and P. fluorescens for Oil Sands

2 mL LB each culture}

Crystored all six strains following Making frozen stocks protocol

stored in iGEM box -- -80°C Lin Lab

Plated LuxS^- and MarC^- mutants and Pseudomonas strains on LB Plated W3110 and MDAI2 on LB+amp+kan

placed all six plates in 37°C ERB 1239

Stored remaining clean LB+amp (6) and LB+amp+kan (8) plates from 7/19 in 4°C ERB 1239

~1.5 hrs

7/22/10

Alex

During Lab Committee meeting -- Moved the six plates from yesterday from 37°C to 4°C

Uploaded Protocol: Culturing CGSC Strains

7/23/10

Alex

Updated Strain Database

7/25/10

Alex and Eric

Made 250 mL LB broth in each of two 500mL flasks

-5 g LB broth
-250 mL DI water

autoclaved 30 min (sterilize time) ~255°C

Autovclaved 250 mL DI water in each of two 500mL flasks

30 min sterilize time, ~255°C

Made a 2mL culture in 15mL tube of W3110

-2 mL LB from 4°C
-2 μL 100mg/mL ampicillin (final conc. 100μg/ml)
-2 μL 50mg/mL kanamycin (final conc. 50μg/mL)

incubated overnight, 30°C, 200 rpm shaking -- 1pm

Left stuff in autoclave

7/26/10

Alex and Marcus

{yesterday, Josh and Charlie removed stuff from the autoclave}

Analyzed yesterday's W3110 culture on Lin microplate reader

endpoint - cuvette - Ex 450nm, Em 520nm, cutoff 515nm (GFP settings)
- blank: 91.591 RFU
- W3110: 117.47 RFU
fixed Ex 450nm - Em spectrum scan - cuvette
- W3110 - Em peak = 520nm (green - good)
fixed Em 520nm - Ex spec scan - cuvette
- W3110 - Ex peak = 370nm (wtf) - still good emission at Ex 450nm
fixed Ex 370 - Em spec scan - cuvette
- W3110 - Em peak = 450nm (wtf)
endpoint - cuvette - Ex 370nm - Em 450nm
- W3110: 1054.9 RFU
- blank: 1934.6 RFU
  - This is some kind of background - very high readings, but the blank is higher than the sample - maybe the GFP in the sample is reabsorbing at 450nm?? At any rate, there appears to be GFP, as expected, and we can probably use Ex 450nm and Em 520nm to detect it.

Autoclaved two 500mL flasks to be sterile containers, each with ~150 mL DI water inside

30 min sterilization (55min total), ~250°C

Alex

Learned how to use Epifluorescence Microscope in HHDow (2nd floor) from Alissa

Viewed yesterday's W3110 culture for GFP
- Unfortunately, no fluorescence could be detected. However, GFP was presumably detected using the microplate reader, so maybe it was just at a very low level. Maybe, the culture was too old (~24 hrs). We will try again tomorrow with a 16-hr culture.
Uploaded Epifluorescence Microscope Usage protocol

Removed glassware from the autoclave --> ERB 1230

Made broth cultures for W3110 and MDAI2

each 5 mL LB + 50μg/mL kan + 100μg/mL amp in a 15mL tube (added 5 μL each of a 1000X stock of each antibiotic)
incubated 30°C, 200 rpm shaking -- 6:30 pm

--Infekt 23:19, 27 July 2010 (UTC)

7/27/10

Alex, Eric and Marcus

Checked OD600 of yesterday's cultures in Lin Lab spectrometer

W3110: 0.873
MDAI2: 0.855

Need to start culture with OD .02

.02 / .873 = 2.29%
.02 / .855 = 2.34%

Obtained 40% glucose solution from Ann - Lin Lab

need .8% glc final conc.
.8/ 40 = 2%

Started 100mL culture of W3110 in 500mL flask

-2.29 mL W3110 culture
-2 mL 40% glucose
-95.7 mL LB

- 100 - 2.29 - 2 = 95.71

Started 100mL culture of MDAI2 in 500mL flask

-2.34 mL MDAI2 culture
-2 mL 40% glucose
-95.7 mL LB

- 100 - 2.34 - 2 = 95.66
placed both cultures in 37°C, 225 rpm shaking - ERB 1230, 11:50am

--Infekt 23:19, 27 July 2010 (UTC)

Marcus and Eric

Alex and Marcus

Checked remaining MDAI2 and W3110 cultures on fluroescence microscope in LSI 6th floor

both seem to fluoresce at GFP equally
- This is probably not right; MDAI2 should not have GFP. Will check on a fluorospectrometer tonight

--Infekt 23:19, 27 July 2010 (UTC)

Alex

Read W3110 & MDAI2 cultures on microplate reader in Xi Lab - SPH

Ex 485nm, Em 545nm (closest to GFP possible on this reader)
- W3110 = 6
- MDAI2 = 5
- Many Acinetobacter controls were run - all at 0 or 1
- This is bad -- MDAI2 is clearly producing GFP, meaning it produces AI-2. Need to contact Tsao authors.

--Infekt 01:47, 28 July 2010 (UTC)

7/28/10

Alex

Made 40 mL of 0.1% crystal violet solution in Xi Lab - SPH

for Ann; will deliver tomorrow

--Infekt 22:02, 28 July 2010 (UTC)

7/30/10

Alex and Marcus - w/ Charlie and Prae

Performed transformation of 5 parts following Transformation-electroporation protocol -- starting from reading OD of overnight. (Ann started the previous steps.)

read OD of overnights (in Lin Lab)
- JW2662-1 (LuxS^-): 1.138 -- bad
- DH5α: 0.710 -- good
made a 1:2 dilution of JW2662-1:LB (48 mL total)
- placed in 30°C, 200 rpm shaking, 30 min
- removed and read OD
  - JW2662-1: 0.657 -- good
Transfered entire 47 mL of each culture to a 50mL tube

Continued with protocol...

following spins and washes, read OD again:
- JW2662-1: 0.42 -- good
- DH5α: 0.87 -- good
electroporated:
- into DH5α:
  - pBAD (for Ann)
  - INP-GFP (for virus group)
  - INP-linker (for virus group)
  - OmpA-GFP (for virus group)
- into JW2662-1
  - pLsrA-YFP (two sources: L14 and 008)
- time constants:
  - OmpA-GFP: 2.8
  - INP-GFP: 2.8
  - INP-linker: 3.2
  - pLsrA-YFP (008): 5.6
  - pLsrA-YFP (14L): 5.6
  - pBAD: 4.8
  - neg. control: 5.0
- incubated all 30°C -- 4:30pm to 7:30pm - 3 hrs
plated on:
- OmpA-GFP: LB+amp
- INP-GFP: LB+amp
- INP-linker: LB+amp
- pLsrA-YFP (both): LB+amp+kan
- pBAD: LB+kan+IPTG
- control: LB+amp AND LB+kan+IPTG
placed all plates in 37°C
excess electroporation culture stored in 4°C

--Infekt 05:17, 31 July 2010 (UTC)

8/2/10

Alex and Eric

Read overnight cultures on Lin Lab spectrometer

OD600 (endpoint)
- LB: 1.156
- W3110: 1.100
- MDAI2: 1.156
GFP fluorescence (Ex 450nm, Em 520nm; endpoint)
- LB: 90.291 (RFU)
- W3110: 190.59
- MDAI2: 180.86
Em 520nm, Ex sweep
- LB: peak 370nm (some kind of background)
- W3110: peak 370nm, kinda bimodal at 440nm (GFP)
- MDAI2: peak 370nm, bimodal at 430nm (GFP)
Ex 450nm, Em sweep
- LB: peak 515nm......wtf
- W3110: peak ~525nm - ok, GFP
- MDAI2: peak ~525nm - GFP
Ex 440, Em sweep
- W3110: peak ~520nm
Ex 440nm, Em 520nm (endpoint)
- - - LB: 117.61
- W3110: 204.86
- MDAI2: 198.34

OK, idk if these have GFP or what. At any rate, if they do, the MDAI2 is too close to W3110. We'll probably ahve to work with the YFP biobrick instead.

Got C. vulgaris from Bobby Levine

~200 mL
strain 258, from flask 085
spun 4200 rpm for 10 min
filtered according to
stored -20°C ERB 1239

Alex and Marcus

Made broth cultures in 15mL tubes

3 mL LB + LuxS^-
3 mL LB + 100

@@ Line 365: / Line 365: @@
 *stored -20°C ERB 1239
 ----
+''Alex and Marcus''
+Made broth cultures in 15mL tubes
+*3 mL LB + LuxS<sup>-</sup>
+*3 mL LB + 100

Team:Michigan/Quorum Sensing

From 2010.igem.org

Revision as of 01:12, 3 August 2010

Quorum Sensing Team

7/7/10

7/8/10

7/17/10

7/19/10

7/21/10

7/22/10

7/23/10

7/25/10

7/26/10

7/27/10

7/28/10

7/30/10

8/2/10