05-10-2010 - Patrick - Anti-Depressor Group: The Terminators!!

So it seems like our competing team isn't doing too well, so we will try helping them out tomorrow if they need it. :)

During the lab today, started off by running the digestions made yesterday on a gel, namely pAT08(E+S) and pSB2K3(E+P).
They looked good and so proceeded to doing a pcr clean up followed by running them on a gel again in order to determind dna concentration for calculations needed for ligations.

Restreaks were made of the ligations plated yesterday, namely pAT09, pAT10, pAT11; if all looks good tomorrow on the plates then O/N cultures will be made.

The pAT12 construct was made today by ligating the following together:
pAT08(E+S) + pAT02(X+P) + pSB2K3(E+P).

A negative ligation control was made as well which contained only the digested plasmid (pSB2K3) and no insert.

• These were then transformed along side negative and positive transformation controls, the positive control had pBR322 as the plasmid for transformation.
• After 1hr incubation at 37C, these 4 transformants were plated and hopefully tomorrow we have some good results.

• The PCR product needs to be run on a gel tomorrow, so lets cross our fingers it will be successful.

05-10-2010 Maya DEPRESSOR group

So today I did a lot of crying... We really need some good results soon!!

I spend the whole afternoon in the p2 lab with Sebastien playing around with Salmonella:-) Hopefully I wont get a stomach infection in the next few days. Well, Sebastien and I made some competent Salmonella cells using the 413 strain (without any phages integrated) and the 421 strain (WT). I then transformed the following plasmids into both strains:

• pIGR01 (pSB4A5+G1+GFP): colony 4
• pIGR02 (pSB4A5+G2+GFP): colony 6
• pIGR03 (pSB4A5+GR1+GFP): colony 11+13
• pIGR04 (pSB4A5+GR2+GFP): colony 16+18

05-10-2010 Annemi Depressor group!!!

Did a PCR of the mini-preps from October 2nd and 4th (see labbook for further detail) but this time diluted 100 fold in water.
However this resulted in yet another depressing empty gel-picture:(
Sebastien suggested that we let the terminator group do a PCR on some of our mini-preps and some of their own (which have been giving nice gel-pictures in the past).
We will do the same PCRs to see if none in the repressor group are able to do a PCR.

Did a PCR clean-up of the restrictions Lisa did yesterday of the backbones: 4A5 and 1C3 and the new biobricks GR1, GR2, Z1, Z2 and RFP. All were digested with E and P.
It looked good on the gel, so we are ready to do some ligations tomorrow.
Maybe the depressor group will have a succes in the nearest future. A girl can dream...

05-10-2010 Juliet and Greg

Wiki: layout improvements in project description. Refactoring of text in project desc. Updates for blog, front page and team.

04-10-2010 Patrick and Anastasiya

We have done PCR clean up of the PCR products from 03.10 (pAT01-1, pAT01-2, pAT08-1) and run them on the gel to verify their sizes. Glycerol stock solutions of pAT01-1 and pAT08-1 have been prepared. Then we have done restrictions of pAT08 (E, S) and pSB2K3 (E, P). Ligation products from 03.10 (pAT09, pAT10, pAT11) have been transformed.

Tomorrow we will do the following:

• restreak pAT09, pAT10 and pAT11
• run digestions of pAT08 and pSB2K3 on the gel
• do PCR clean up

3 & 4-10-2010 Repressor group Lisa

we did PCR on minipreps - and there are nothing going on in the PCR. What are we doing wrong?
we will try to make a dilution of template DNA.
We could try a digestion check, and maybe we could just use E+P as check enzymes.
we made O/N cultures of restreaks from 2-10-2010. And the interesting one of these were miniprepped - didnt have a look at gelpicture yet.
Digestions were made of products needed for making the plasmids that were submitting as biobricks, these need to be PCR-cleaned and then they should be ready for ligation.
Plating of O/N culture which should contain plasmids with pBADZ2 +RFP together with L-arabinose. If we get red colonies we know that the construct (pBADZ2 +RFP) is actually present
I had a look at colonies from transformations that should contain pIGR01, pIGR02, pIGR03 and pIGR04 in FLemmings microscope. In a few of the transformations with pIGR01 and 02, there are good fluorescence, but in the rest it is poor ( Sebastien says that this could be background fluorescence from E. Coli??). In colonies containing pIGR03 and 04 (containing promoter and repressor) there is also fluorescence, but this is reasonable since the system is not tight..
Tomorrow Maya will transform Salmonella with pIGR03 and 04 and pSLD20 and 22 (containing antirepressors), and hopefully we can get some highly glowing colonies.

04-10-2010 WIKI References (Malthe)

Hi team I have with support from Juliet and Greg, tried to set up a footnote or reference system on our wiki, igem have not intalled the application needed and thus the references have to be typed in with text. se example in the "Project" page.

04-10-2010 - SDU DTU iGEM conference - Malthe

Update: We have booked the seminar room here in 301, to avoid problems with keys ect. Regarding food i talked to Lene Krøl (info below). we decided that either we get a "factura" and give them and they pay. when this is not possible, when shopping in a supermarket, we pay and get the money refunded, save the receipt.

03-10-2010 - Thomas - Antiterminator group

Juliet and I were in the lab today the group. We ran a gel of the 30 verification PCRs that were done yesterday, as well as the four restriction digests. The verification PCRs showed that pATN and pAT08 were both successfully ligated and that the pAT11 ligation failed. We're unsure about the pAT01 ligation, there were strong bands for all four minipreps done, but one of the inserts was larger than the other three. The one that was larger was also the one we thought was closest to the expected size. We ran three PCRs, two of pAT01 (to further verify it) and one of pAT08 so it will be ready for restriction tomorrow.
The digestions of pAT02, 04, 06 and 07 all looked ok and were used to run three ligations, plasmids pAT09, 10 and 11.

02-10-2010 Anastasiya & Patrick Anti-terminator group

Re-did the digestions on pAT02, pAT04, pAT06 and pAT07 that Thomas managed to kill last night.. :p They were ran on a gel and seem to be good, PCR clean ups were made on them and they need to be ran on a gel again to determine the dna concentration, so this is one of the tasks to do for tomorrow. Freeze solutions were made of pAT02(L1-2), pAT06(L2-4), pAT07(L4-4) and placed into our strain bank in the -80C freezer.
Mini-preps were made of the over-night cultures containing pAT01, pAT08, pAT11 and pATN(N+1C3), these were then ran on a gel as well as used for PCR verification. If no one else from the building takes out the PCR tubes from the PCR machines, then remove them tomorrow and run them on a gel to see if our ligations were successful.
As there was no more space in our functional parts only box, I started a new one called functional parts only box #2 and the new mini-preps can be found in there.
The digestions mentioned above can be found in the working box, which is pretty much filled up, so a new one should be started of those as well.
If all the verification PCR's turn out to be good tomorrow, I suggest getting started on the next set of pATxx series and pushing forward as much as we can to get our construct done.. awesome work so far!!

02-10-2010 Repressor group Annemi

Made minipreps of the overnight cultures from yesterday. Made with 4mL culture. They are stored in the freezer in a blue thingy. Should be easy to find. Ran a gel of the minipreps.
The T-group grabbed the thermal cycler before me, so I didn't make the PCR on the minipreps. But from the gelpicture it looks like we might have an insert:)
Did restreaks of the transformations which had grown.

01-10-2010 - Thomas - Antiterminator group

Ran a gel of PCR products of pAT02, 04, 06 and 07 (from 30-09) and then a PCR clean up and another gel of that. Both gels looked good, each band was the expected size. The purified PCR products were then digested with X and P.
Overnights were also done of the pAT01, pAT08, pAT11 and N+1C3 restreaks from thursday 30-09.

01-10-2010 Repressor group Maya and Lisa

The restriction products from yesterday (G1, G2 and RFP), and the PCR products RFP and GFP were purified and run on a gel. Everthing looked good, and this was the first time that we could actually see G1 and G2 on the gel after restriction. This was probably because two pcr products were pooled in one clean-up, and because the restriction was done in only 50 ul total volume rather than 100 ul.

We re-did some of the ligations that didn’t work yesterday. These were:

• L1: pSB4A5 + G1 + GFP (Did work yesterday, but was repeated anyways)
• L2: pSB4A5 + G2 + GFP (Did work yesterday, but was repeated anyways)
• L5: pSB2K3 + BADZ1 + RFP
• L6: pSB2K3 + BADZ2 + RFP
• L8: pSB4A5 + RFP
• L9: pSB4A5 no insert
• L10: pSB2K3 no insert

01-10-2010 Dry Lab - Anja

30-09-2010 Dry Lab - Anja

nice that the dry lab people also are allowed to write in the Lab blog now :-)

• preparing meeting agenda and keeping track, tomorrow I will write a summary and send out reminders
• search for more shipping information and when we should send our biobricks
• DNA submission, I got more into the details and its important to note, that the registry needs to be filled out before we are able to send the BB
• I also continued to write for the Wiki and this I will do tomorrow as well as we talked about in the meeting, writing a summary about the repressor system and short about characterization for poster purposes

30-09-2010 Anastasiya Antiterminator group

Thomas and I have done 2 PCR verifications on each of the MiniPreps prepared on 29.09, corresponding to ligation products L1-L5 namely of pATO2, pAT06 and pAT07. We run 40 PCR reactions in total. (For further information see our lab book) Then we run them on gel to verify their sizes and see if they worked. It seems like all of them have worked except from pAT06, but likely we have run it twise and at least one of them worked.
Then we have chosen one of L1-L5 for further PCR and we have also done another PCR of Mg03&IC3.
We have also restreaked colonies from L1, L2, L3 and L7 plates from 29.09.

Tomorrow the following should be done:

1. PCR products should be verified on the gel followed by the PCR clean up
2. Restrictions of PCR products
3. Preparation of the overnight cultures of the restreaked L1-L3 (5 of each)

30-09-2010 Maya Repressor group

Annemi's 40 PCR reactions from yesterday didn't give any result, meaning that we still haven't succeeded in ligating our biobricks into pSB1C3. We will put this on pause for now and concentrate on ligating our biobricks into pSB4A5/pSB2K3 with GFP/RFP.
The ligations made yesterday L1-L10 were somewhat successful. All transformations besides the ones containing RFP gave colonies. Today we restreaked these colonies and tomorrow we can do O/N. We also restricted G1, G2, and RFP so we can redo those ligations that didn't work.
Annemi made a PCR og RFP and GFP. These will be purified and run on a gel tomorrow.

29-09-2010 Greg Repressor group

Got in touch with students using the BioLector (Manos and Jacopo). Made a tentative booking for weekend 9-10.10.10 (Friday 8th also possible). Jacopo will explain how to use the equipment a few days before we run the plates. Recommendation is to measure OD of a culture grown outside of Biolector (but in the same medium) to have an estimate of when best to treat with arabinose (this applies to the antirepressor system). Should treat during exponential phase. Also it's important to prepare the plate under the hood, to avoid contamination.

29-09-2010 Annemi Repressor group

Made ligations of the following:

• L1: pSB4A5 + G1 + GFP
• L2: pSB4A5 + G2 + GFP
• L3: pSB4A5 + GR1 + GFP
• L4: pSB4A5 + GR2 + GFP
• L5: pSB2K3 + BADZ1 + RFP
• L6: pSB2K3 + BADZ2 + RFP
• L7: pSB4A5 + GFP
• L8: pSB4A5 + RFP
• L9: pSB4A5 no insert
• L10: pSB2K3 no insert

29-09-2010 Thomas & Patrick Antiterminator group

Started off the day by making ligations of our constructs: pAT01, pAT08 and pAT11. These were then transformed and plated; they will be ready for restreaking tomorrow and innoculation of overnight cultures on the subsequent day. Mini-preps were made from the over-night cultures containing our constructs pAT02, pAT06 and pAT07; these will be PCR verified tomorrow.

28-09-2010 Patrick Antiterminator group

Digestions were made today of nutR and nutR+terminator both with restriction sites of XbaI and PstI; these will be used tomorrow for ligations of constructs pAT08 and pAT11, respectively.
Mini preps of Mg03, Mg03+1C3, N+1C3, nutR+1C3 as well as puc19(one of Sebastien's high copy number plasmids) were made today, a few made in parallel while Sebastien did them as well, intention of this was to test whether mini prep skills were faulty or whether the plasmids are in deed crap.
The restreaked plates containing our constructs of pAT02, pAT06 and pAT07 were used for innoculation of overnight cultures; these will be mini-preped tomorrow.
PCR clean ups were made on the pSB2K3 PCR products as well as the digestions of the above mentioned products after digestion was performed.

28-09-2010 Greg Repressor group

Moved last year's layout to the home page. The links have been updated and should work (let me know if they don't).

28-09-2010 Annemi Repressor group

Today the PCR of G1, G2, GR1, GR2, BADZ1 and BADZ2 was redone and it looks good:)
Restrictions with E+S was made on G1, G2, GR1, GR2, BADZ1 and BADZ2 (old PCR products).
6 mL of the transformation overnight culture (still from last week) was spun down. This will hopefully result in a mini-prep with a higher concentration than the ones Maya did... Miniprep was made and they are stored in the working box: no label. Only number (corresponding to the original colony) and date.
Lisa did cleanups of the PCR products and the restrictions.
Maya made restrictions of pSB4A5, pSB2K3, RFP, GFP as well as cleanups of these.

Tomorrow we should be ready to some ligations.

27-09-2010 Maya Repressor group

The PCRs I made the 24-09-2010 were ran on a gel i the weekend and no bands appeared:-( Maybe something is really wrong, or maybe I'm just really bad at making PCRs. Sebastien had a look at the gel picture with the purified plasmids that I used as templates and thinks that they look weird. He thinks the concentration is way lower than normally, and he also thinks they look like cut plasmids. So I'm not sure whether we should attempt a new miniprep or whether we should make a new PCR on the miniprep I did, or start all over... We did after all have a lot of background in this ligation, so maybe its a good idea to start over. Sebstien also mentioned that it could be a problem to try to clone the gifsy repressors into pSB1C3 which is a high copy number plamid, and as far as he understood it, the IGEM headquarter allows submission in other plasmids if you have an explanation for not using pSB1C3. So I guess we could just submit in pSB4A5. Anyways, we can talk about this tomorrow as I'll come in at 8 am.
Today Anja did a PCR of G1, G2, GR1, GR2, Z1 and Z2, but none of them worked, so they have to be redone tomorrow.

27-09-2010 - Anastasiya & Patrick - Anti-terminator group

Restreaks were made of ligation plates of L1 to L5 that can be found in the lab book dated 23rd September 2010. Over night culture media (already containing antibiotics) are ready and stored in the fridge, these will be used for the colonies obtained from the restreaks mentioned above.
The verification PCR's from friday (24/09/2010) were ran on a gel, all except for one band had the right sizes; the band corresponding to the N anti-terminator didn't fit in size so another PCR verification was performed. Another PCR of GFP+RBS was made today as well.
A PCR clean up of RBS-N(X+P) was ran on a gel in order to perform calculations required for ligations.
Along with this gel, PCR amplified plasmid backbones of pSB4A5, pSB1C3 and pSB1A3 were ran to verify that they were still present after they had a little swim on friday.

25-09-2010 Repressor group Maya

Yesterday I was in the lab alone, but fortunately Patrick was kind enough to help me out a bit. I did minipreps of the 20 O/N (5 colonies from each transformation) that Annemi and I did yesterday. These minipreps hopefully contain our PCR products (G1, G2, GR1 and GR2) in the pSB1C3 backbone. After the miniprep I did 40 PCR reactions on the plamids. All plasmids were tested with two sets of primers - the VF1 and VR primers and also with our IGR01/IGR04 & VR primers. Today I'll go the lab and put the PCR products in the fridge, and if I have time I'll run them on a gel as well.
The forward primers that I orderd for the antirepressors also arrived today, so next week we can do a PCR of the antirepressors and ligate the products into pSB1C3.
Unfornately someone forgot to put Annemi's restricted products from the 23-09-2010 in the fridge after having run them on a gel. So these are most likely not working anymore, and have to be redone before we can do the ligations of G1, G2, GR1, GR2 + GFP. Sebastien told us that if restricted products are not kept on ice, the sticky ends possible get degraded.

24-09-2010 - Thomas - Antiterminator group

The transformations of our ligations from yesterday look really good! :). There are only about 8 colonies on the ligation control, and 20+ on the plates with the actual ligations. We restreaked 4 colonies of each of the 5 ligations and put them on the lab bench to let them grow over the weekend. On Monday we should start some overnight cultures of all 20 restreaks so we can miniprep and verify them on Tuesday.
Patrick and I also did PCRs of the pSB2K3 backbone plasmid and the RBS+GFP. In addition to that we did 9 verification PCRs on the minipreps of our ligations from last week, so hopefully we'll get some good bands there! The PCRs will finish just before I leave the lab (wow, it's already 17:30...) so I will put them in the fridge so they can be run on a gel on Monday.

23-09-2010 - Thomas - Antiterminator group

Unfortunately, I was in the lab alone today, due to half my group being on vacation. Since I had to prepare the presentation for the meeting with our supervisors and the 2009 team in the afternoon, not alot got done in the lab. I transformed the ligations that Patrick did yesterday, with Anja's help, and plated them. Anja ran a gel of the PCRs of the plasmids backbones that Patrick did yesterday and they all looked good. Anja also did a miniprep of the MG03 plasmid :).

23-09-2010 Maya Repressor group

Today we got the proof that the plasmids pSLD20 and pSLD22 have been mixed up during O/N or miniprep. This means that the plates we have in the fridge are correct, but that the plasmids are swapped in the glycerol stock. We haven't corrected the naming, but will do that tomorrow.
Annemi and I spend most of the afternoon talking to Sebastien about the problems we have had with the colony PCR and also with the background we got when we did the transformations. As the colony PCR Annemi did yesterday didn't work, Sebastien advised us to do the PCR on the purified plasmids. Therefore we started O/N, and tomorrow I'll do miniprep and a PCR.
Regarding the background we got when we transformed the ligated plasmids, Sebastien came up with several strategies to solve the problem. We talked about them at the meeting today, and they will also be written here in the log tomorrow or the day after.

22-09-2010 Annemi Repressor group

Colony PCR on transformations G1, G2, GR1, GR2. Same approach as Lisa did yesterday, however we marked the colonies this time:)
We used 3 different forward primers: IGR01 (for G1 and GR1), IGR04 (for G2 and GR2) IG201 (for all of the colonies). The same reverse primer IG202 was used in all of the reactions.
Result: only two bands appeared; one which corresponds to the size of amplified G1 and the other one to G2.
Questions: Why didn't the iGEM primers IG201 + IG202) amplify anything? Digested plasmid? Why did Lisa get so much more bands yesterday?

Restrictions:

• GFP+rbs: cut with X+P
• pSB4A5: cut with E+P
• G1: cut with E+S
• G2: cut with E+S
• GR1: cut with E+S
• GR2: cut with E+S

22-09-2010 Maya Repressor group

We still haven't figured out what happend to the plasmids pSLD20 and pSLD22, so we restreaked both the ones from the glycerol stock and the ones in the fridge.

To Anja:
I think it would be most efficient if you spend the morning doing dry lab stuff. Could you maybe prepare the meeting agenda? There are a few points on the sheet of paper on the wall in the student room. We will start the meeting with a presentation for the supervisors (Thomas is making that one), and after that (probably at 5 pm when everyone is present) we will have our normal weekly meeting. So if you could make the agenda for the normal meeting.
When that is done, you can just continue on the paragraph you are working on for the wiki.
Annemi and I will come at 1 pm, and hopefully we will do some ligations.
Just send me a message if you have any doubts:-)
Have fun!!

22-09-2010 - Patrick - Terminator group

Another long busy day with many items to take care of.
The digested items from yesterday were purified via pcr clean up, and ran on gel to determine concentration for ligations.
After this, all items needed for ligation constructions of pAT02, pAT06 and pAT07 were ready.

The following ligations were made:
L1: pAT02 - RLN + RBS-RFP + pSB1C3
L2: pAT06 - nutR + B0011 (X+P) + pSB1C3
L3: pAT06 - nutR + B0011 (E+X) ( <-- pSB1A3)
L4: pAT07 - nutR + B1003 (X+P) + pSB1C3
L5: pAT07 - nutR + B1003 (E+X) ( <-- pSB1A3)
L6: Negative ligation control - pSB1C3
L7: Negative ligation control - B0011 (E+X)
L8: Negative ligation control - B1003 (E+X)

Tomorrow (23/09/10) these need to be transformed and plated.
Plasmid purifications were made from the re-streaked ligation plates, the following mini-preps were made:

1. Mg03 + 1C3
2. nutR + 1C3
3. N + 1C3

1. pBAD (E+S)
2. RBS-N (X+P)
3. pSB4A5 (E+P)

1. pSB4A5
2. pSB4A5
3. pSB1C3
4. pSB1C3
5. pSB1A3
6. pSB1A3

1. GFP+RBS
2. plasmid backbone pSB2K3

21-09-2010-Lisa - Repressor group

A new PCR with pBAD, BADZ1 and BADZ2 turned out to be succesful, as Annemi wrote (using miniprep 1 as template) - although it seems that there is confusion about which plasmid is pSLD20 and which one is pSLD22. Sebastien says to trust the PCR products! and he might have an explanation for the mix up. Talk to him tomorrow.
You should also check the re-streaking of the strains with the 2 plasmids on CAM-plates - these restreakings were done from the glycerol stock. pSLD22 should have CAM resistance and pSLD 20 KAN resistance. THe re-streaking that Maya did yesterday came from plates and showed as expected that pSLD 20 has KAN resistance
I did another PCR with pBAD, BADZ1 and BADZ where I used miniprep 2, to check if these templates also seem to be switched. The PCR products needs to be run on a gel - they are probably still in the PCR machine.
I did a colony PCR on 3 colonies from each of the transformations. Check the picture in the lab-book. I didnt have time. The first lane is ladder, the next 5 is Patricks, and the next 15 are ours. I think I forgot to write that the last 3 lanes contain a PCR of the "no insert".
We should change the colony PCR strategy to Annemi's boiling strategy, as this turned out to be quite succesful.
Finally I did a PCR clean-up of the PCR products from the PCR with miniprep 1 as template - products still need to be run on gel, and maybe they are ready for digestion :)

21-09-2010 - Patrick - Terminator group

Today the lab work was ran almost parallel with good success with the repressor group, Lisa and I had a rather successful day. To start off with, the PCR's in the morning.. WORKED!! Those were both from the repressor group and terminator group.
I continued to work on the digestions needed for our construct and did the following ones:

• GFP(rbs): E+S
• pSB1C3: E+P
• pBAD: E+S
• pSB4A5: E+P
• pSB1A3: E+P

21-09-2010 - Annemi Repressor group

A new attempt to amplify pBAD, pBADz1 and pBADz2 was made. The PCR was made exactly as Maya made it yesterday (see lab-book for further details).
Patrick and I made some changes in the restriction protocol which can be found in the protocol folder in dropbox.

20-09-2010 - Patrick and Anastasiya - Terminator group

So today we've been doing a bit of work for both the terminator and repressor group. Firstly we ran 2 pcr's on plasmid backbones (pSB1C3 and pSB2K3) which turned out successful on the gel, they were then purified via pcr clean up. (Please take note here that the old pcr buffer was used, so I suggest from now on when running a pcr, use any buffer you think will work, but use the old buffer as a form of control with an extra pcr product, so that in case it doesn't work but the control does, the problem might be the buffer and not your pcr.)
Digestions that were made on Thursday (16/09/2010) were ran on a gel, most of them weren't very visible, but successful non the less; they were purified as well via pcr clean up.
The ligation plates plated on Wednesday (15/09/2010) were restreaked and will be ready tomorrow for inoculation of over night cultures.
We also helped out Maya, and did pcr clean ups on the pcr products of the plasmid backbones, they all seemed to have worked well (pSB1C3 wasn't as strong as the others though) the only pcr product that appeared to have not worked was that of GFP, details on this can be found in the lab book, but it should have something to do with the pcr buffer again as there were 2 pcr products of GFP, one worked and the other didn't.

20-09-2010 - Maya -Repressor group

The PCR Lisa and I did Friday only worked for the pBAD promoter, not for the pBADAntO or pBADAntT. So today I redid the PCR using each primer set on both pSLD20 and 22 just in case Sebastien messed up the labeling of the plasmids. I also restreaked the pSLD 20 and 22 on plates with CAM and KAN to verify whether Sebastien did indeed mess up labeling. Patrick will run the products on a gel, and place the photo on our desk today. If the PCR is still not working we should talk to sebastien about alternative ways of amplifying the products.
I also transformed the ligations Lisa and I made Friday, and hopefully you should see colonies tomorrow. If there are colonies you should restreak them on new plates tomorrow, so that we get more clean colonies.
The terminator group is still working on amplifying the GFP as the GFP without RBS didn't work. Apparently the plasmid is gone, or they can't find it, so they are redoing one of the PCRs using the PCR product with the RBS as a template.
I made a new box in the freezer for our group, so that we now have a box with verified PCR products and minipreps, and one box with stuff that are not necessarily going to be saved (working box).
One thing you could also do tomorrow is to have a look at that excel sheet called "Parts and plasmid list-repressor group". We need to past in plasmids that we have purified and constructed.

17 -09-2010 - Lisa and Maya - repressor group

Gel of the purification of G1, G2, GR1 and GR2 looked good, we did ligations of these parts with the plasmid pSB1C3 - these ligations should be transformed monday (20-09-2010).
Plasmid purification of overnight cultures with plasmids pSLD20 and pSLD22 also looked good, so we did a PCR to obtain the pieces pBAD, BADZ1 and BADZ2. These PCR products should be checked on gel monday - finally we made glycerol stocks of the overnight cultures (pSLD20 and pSLD22).

16-09-2010 - Maya and Annemi - repressor group

We did a restriction on our PCR products (G1, G2, GR1 and GR2), and of the plasmid pSB1C3. The plasmid is going to be used for submission of the biobricks. The restrictions were purified using the PCR purification kit. The purified products still need to be run on a gel. If the gel looks good tomorrow, a ligation should be done.
The missing primer arrived today meaning that tomorrow a PCR of GFP can be done. Both groups need the GFP.

16-09-2010 - Anja - repressor group

• I did the clean up of our PCR products, they are labeled as those. Afterwards I run them on a gel to control the presence of PCR products after the clean up procedure.
• I started an O/N of pSLD 20 and pSLD 22 with 100 Amp and incubated them at 37 degrees.
• Never take ligase and restriction enzymes from that other lab into our lab - people are panicking if their beloved enzymes aren´t there and want to order immediately new enzymes! ;-)
• All tubes for storage have to be labeled with stickers, but don´t use the blue ones. Write clearly: sample, date and what has been done. Otherwise you get in trouble with Annemi ;-)
• Use lab book for writing messages to each other.
• Write down in lab book, what next days people should continue within the first hours (you don´t have to plan the whole day for them, but at least that they can start easily (and early ;-)).

15/09/2010 - Terminator group - Thomas & Patrick

Today we did digestions of N, NutR, MG03, pSB1C3. After PCR-cleanup the N and NutR digestions seemed to have worked but you can't see a difference from digested/non-digested as they are from pcr products. The MG03 digestion looks bad, but the dna concentration might have been too low. The pSB1C3 also had a low dna concentration. Tomorrow we will still attempt ligations and redo digestion of both MG03 and pSB1C3. We should also pcr more linear pSB1C3 plasmid backbone.

14-09-2010 Anja (Repressor group)

Lab stuff:

• Annemi minipreped the overnight BB transformation cultures from yesterday. She minipreped only half of the O/N, because Malthe and Annemi think we have enough plasmid to work with (Correct?).
• those minipreps labeled with white stickers are stored in the -20 degree freezer in a box with date 14-09-2010
• A back-up preparation of the transformants has also been made. 2x2mL of cells have been centrifuged and the cell residue is kept in the -20 degree freezer (white stickers: date, biobrick/plasmid #, 'cells') This will make it easier to prepare a new mini-prep since we don't have to grow overnight cultures first.
• a gel of minipreps has been run and I took a picture. Seems like the mini-preps went well since a band is visible in all of the wells.
• Glycerol stocks of transformant cells have been done and stored in the -80 degree freezer
• OBS they reorganized the freezer > look into lab book "freezer box location"
• Malthe has resuspended our primers, which arrived today :-)
• One primer is still missing, Malthe wrote an email to ask for primer IGT02

• Look for a big 2 L box in the fume hood in our lab next to the sterile bank. It´s refilled by Bjarne.
• Go downstairs to room 162 on the 2th floor with a min. 1L bottle. The room is on the right side, go to opposite room, get keys and book from cupboard right to the door. Write in the book, how much you have taken.

15. sep. 2010 Annemi

Today we have run PCR´s to amplify the promoter region and the repressor region. We used 2µL of Sebastiens Salmonella DNA number 143 as template. (See the lab book for further detail on the procedure)
The program used to amplify the small fragments (ca. 100 bp) are called IGEM TD 100BP
For the larger fragments we used Sebastiens program: SebFC
The products are run on a gel (3-2-1)
We made transformations with the plasmids pSLD20 and pSLD22 in the DH5α. The cells are plated out on AMP-plates (20µL and 200µL)

13-09-2010 Maya (repressor group)

Today me and Anastasiya did O/N cultures of the biobricks that we transformed last week. Tomorrow we need to do a miniprep on all of these plasmids, and also prepare some glycerol stocks. We made double of the O/N so there should be enough if you want each group to have their own sets of purify plasmids.
If the primers arrive tomorrow you should also resuspend them, organize them in a "repressor group" box and make dilutions.
I've started on another A3-sheet describing the construction of the three different setups in parallel. Maybe you can continue on that or improve it. The purpose of the sheet is to make it easier for us to see which things should be run in parallel. In that way we can do all the PCRs at the same time and so on.
If you have time Lisa, you can continue on the CLC files. I'll try to finish mine today.
I also think we should find out who is going to write what on the wiki, as I think our group should write about the gifsy1 and gifsy2 promoters, the repressors and the antirepressors.

080910 Maya and Annemi (Repressor group)

We now have a strategy on how to do the labwork in the repressor group. We will need to construct six different plasmids:
pIGR01 (GF1) /pIGR02 (GF2): A pSB4A5 backbone plasmid with the two promoters pRM and pR. Downstream of the pR-promoter we will have a GFP.
pIGR03 (GF1) / pIGR04 (GF2): A pSB4A5 backbone plasmid with the two promoters pRM and pR. Downstream of the pR-promoter is a GFP. Downstream of the pRM-promoter is the gogR and gtgR respectively.
pIGR05 (GF1) / pIGR06 (GF2): A pSB2K3 backbone plasmid with a pBAD/araC promoter. Downstream of the promoter region the anti-repressor antO/antT (GF1 and GF2 respectively) is located. As a reporter the BioBrick RFP (E1010) which is located downstream of the anti-repressor.
The plasmids will be transformed into competent cells and fluorescence will be measured with the BioLector. All of the plasmids will be transformed separately along with the following combinations:
pIGR01/pIGR02 Expected outcome: GFP will be detected
pIGR03/pIGR04 Expected outcome: GFP will not be detected
pIGR05/pIGR06 Expected outcome: RFP will be detected
pIGR05 + pIGR03 Expected outcome: Both GFP and RFP will be detected
pIGR06 + pIGR04 Expected outcome: Both GFP and RFP will be detected
pIGR05 + pIGR01 Expected outcome: Both GFP and RFP will be detected
pIGR06 + pIGR02 Expected outcome: Both GFP and RFP will be detected
As a control we will use a pSB4A5 backbone plasmid only containing GFP.

• Overlapping primers which we will use to amplify the two promoters pR and pRM as a BioBrick have been designed.
• The primers to amplify the gogR/gtgR and the promoters from the Salmonella chromosome as a BioBrick have been designed.
• Primers to amplify pBAD/araC and antT/antO from the pSLD20/22 plasmid as a BioBrick have been designed.
• Primers to amplify GFP still need to be designed. How about the RBS and terminator?

31-08-2010

IGEM UPDATE: 31-08-2010 (copied to log) The Result of the Day, and what we talked about. BB REGISTRATION - REPRESSOR & ANTI-TERMINATOR

• Each research group register the biobricks needed and in our excel sheet note when the file have been added to the registry, becouse then no further editing should be done in the excel file.
  - see "our biobricks list and sandbox.doc" in Research group.
• The needed description is written in the excel sheet - see "our biobricks list and sandbox.doc" in Research group.
  - Enter a long description of the part so that users of your part know what it is, what it does, and how to use it in their projects.
  - Enter the source of this part. For example, does it come from some genomic sequence?
  - Enter any design considerations you had to deal with during the detailed design of the sequence
  - After which we have to enter the sequence and add feature annotations.
  

• Group picture
• Wiki presentation, frame set up by Juliet. presentation of what to be filled out.
• tech-track

• Go to our team page, and look at our team roster make sure your information is typed in correct. this will be on your certificat for attendign iGEM.
• Come up with 3 good applications for our stable "real" bistable switch system, as we need to select track on friday.. (or think about it) we collect them friday, and put them on the wiki.
  AREAS:
  
  • Final Tracks
  • New Application
  • Food/Energy
  • Foundational Advance
  • Health/Medicine
  • Environment
  • Manufacturing
  • Information Processing
  • Software Tools
• tech-track

• Maya and Malthe have made an improved Gant Diagram (again) take a look at it and feel free to add to it.
  • 31_08_V001_MMB_MFK_OVERALL TIME PLAN.xls in the management folder.

24-08-2010

So the competent cells we made last week have been infected by phages!!! Oh no, this is really bad cuz it's difficult to get rid of phage contamination. Sebastien thinks that it might be a T1 phage. So we are preparing to make a new batch of competent cells. This will be done Friday. All the pipettes have been cleaned thoroughly to get rid of potential contamination.
Still working on the biobrick design. We are reading a lot about biobrick standard measurements, and we have found a lot of interesting papers. The design isn't as easy as initially thought if you want to get some data corresponding to the iGEM standard.
Maya

20-08-2010 (Patrick , Malthe , Anja, Juliet and Maya)

To make it easier for everyone to follow the project I'll try to give an update on what has been going on this week.
First of all we have had two meetings, one group meeting and one meeting with the supervisors. Summaries of the meetings can be found in dropbox in the management folder.
We have spent a lot of time on getting an overview of the project, and we have tried to make a phase diagram of what should be done for next two months.
Juliet got the Wiki up and running and is trying to work out how we can do the modeling with fictional data. She is also having a meeting today with Steen to get an overview of the economy. Remember to let her know whenever you spend some money from our account!!
The characterization of biobricks have a really high priority at the moment. So mainly Malthe and me (Maya) are trying to come up with several stragtegies on how to do this and which biobricks we should focus on. We hope that by next week we have a long list with some thought out projects. The idea is to distribute the projects among the lab group so that each person/group of two gets his/her/their own project. The responsible persons should then finish the design and start on the lab work. Some of the mini projects are most likely not going to work, so that's why it's a good idea to have several.
We have also come up with a new naming system for all our parts as this is really needed when you work with the parts in the lab. This list can be seen in the research group folder-> "our biobrick list" All the parts found in the list should be registered in our "sandbox" in the partsregistry. When we start working on our biobricks, all information should be typed directly into the sandbox. When characterizing a BB Biofab, drew Andy's company have made a data sheet see our wiki

• https://2010.igem.org/Team:DTU-Denmark/Project#characterizing_our_Biobricks

Whats going on in the lab (12/08/10) (Annemi, Patrick)

So if you have done your homework and read yesterdays log ;), you would have a better understanding and update of whats going on with the project. Heres whats actually going on in the lab right now:

• From the power-point presentation "Bistable switch design - Biobrick approach" , if you have a look at slides 6 and 9 this will illustrate what we are trying to put together.
• We are digesting and ligating by the method of biobrick assembly standard as was mentioned yesterday.
• We are digesting and ligating by the method of biobrick assembly standard as was mentioned yesterday.
• Initially we ran into problems with the restriction enzymes (FastDigest enzymes from Fermentas), after a third attempt and playing around with the digestion mix, we got them to work.
• We are hoping to be successful in our ligations, which we will be transforming today (fingers crossed for tomorrows outcome ;)), the plasmid backbone used for the ligation is pSB1T3, a high-copy number plasmid that has the Tetracycline antibiotic resistance.
• Plates containing tetracycline need to be used within 2 weeks after being made as the tetracycline antibiotic is unstable. If you have to make some of these plates as we have to, ask Lisa for the protocol for making plates. You can also ask Bjarne, the lab technician in our lab for assistance. After you have gone through the laborious procedure of making your LB solution, you need to add the antibiotic (the solution can be max 60C otherwise the antibiotic will die).
• Today the tetracycline plates made will have a concentration of 10 gamma.

Lab work - follow up (11/08/10) (Lisa, Annemi, Thomas, Anja, Anastasiya & Patrick)

As the log was supposed to be updated according to the successes based upon construction of a template plasmids containing the FP's, the reason why this never occured is because it never worked and a huge change in the project occured.
After having performed the same procedures as was mentioned in the previous log entry, the colony PCR results indicated a zero success rate at constructing the FP template plasmids.
The new biobrick approach (Annemi, Patrick, Thomas, Lisa) :
A new biobrick approach was engineered to put our whole system together. We scratched the idea of using red swap to insert our half switches into the chromosome as these were not biobrick friendly..
Instead we came up with the idea of having "mini-genes" synthesized and thereafter assembled together in the manner of the biobrick assembly standard. This also means that we can in the end submit all of our pieces as biobricks.
All the mini-genes and corresponding primers have already been ordered and we're still awaiting the arival of the mini-genes.
Dr. Thomas has created a powerpoint presentation illustrating how these mini-genes are to be assembled and how everything will look like in the end.
The powerpoint presentation, called "Bistable switch design - Biobrick approach", can be found in the "Step-wise construction and in-silico model" folder in dropbox.
As you all should know, the biobrick assembly standard uses 4 restriction sites, 2 in the prefix: EcoRI (E) & XbaI (X) and 2 in the suffix: SpeI (S) & PstI (P).
Whether having to assemble biobricks taken directly from the dna distribution kit or the mini-genes, the concept would be the same and you need to follow the assembly standard.
If you need to refresh your remember about this procedure, have a look at the file "BioBrick_Assembly_Manual" which can be found in the "Research Group" folder in dropbox.
As we are under quite a bit of pressure to construct our system, the positive side of this approach is that it should be rather easy to assemble everything as long as a lot of thought is put into the digestions and ligations. ;)
In terms of actually activating the system, to start with we won't be using the light-receptor mechanisms, instead we will initially test / activate the system based upon carbohydrate sources, namely rhamnose and arabinose.

Lab work (Patrick, Anastasiya and Anja) 06/07/10

After last weeks succesful ligation of CAM and KAN resistance markers into plasmid pSLD3, we successfully constructed plasmids pSLD30 (which contains CAM) and pSLD31 (which contains KAN). All the steps and how we calculated the volumes needed of all the items for both restriction and ligation can be found in the lab book. Long story short, in order to have ample amounts of inserts, (FP's and resistance markers), we performed PCR's.. both de-novo amplifications of the inserts that weren't present as PCR products from Sebastien already, and re-amplications of the PCR products available from Sebastien. Once PCR was completed, we had ample amounts of all the FP's (yGFP, CFP, and CRFP) as well as resistance markers (CAM & KAN).
Next step was to perform a PCR clean up; in order to construct pSLD30 and pSLD31, for now we were only working with the resistance markers.. FP's will come in the picture at a later stage. So, a PCR clean up was performed (follow protocol) on the PCR products of CAM and KAN. These are now ready to use for the next step, which were restrictions.
The primers used when performing PCR on CAM and KAN had tails which contained restriction sites, which brings us to the point using restriction enzymes. The table with all the combinations of restriction enzymes used for each digestion can be found in the lab book, the point was to perform restrictions such that in the next step we could ligate plasmid with insert in the combination of:

• pSLD3 + CAM = pSLD30
• pSLD3 + KAN = pSLD31

• PCR
• PCR clean-up
• Restrictions
• Gel-control of restrictions
• Ligation
• Gel-control of ligation
• Transformation
• Plating
• Over-night cultures
• Plasmid purification & -80 freezing cultures

Lab work (Thomas, Anja, Patrick and Maya) 25/06/10

Today Thomas joined the lab:-)
The 10-1 and 10-2 dilution from the 24/06/10 yielded several hundred colonies which means that the transformation was indeed alright. As it's Friday today, we will wait with the O/N culture till Sunday.
The O/N of strain SP58 showed growth this time. The plasmid was purified and stored together with the FP plasmids. A -80 freezing culture of this strain was also made.To get an overview of the strains and plasmids we have used so far, have a look in the strain and plasmid bank in dropbox-research group-strain and plasmid bank.

You can't spell funding without fun... (Annemi) - 25/06/10

I had a look at some funding and where we should go from here.

• We should definitely apply for the COWI fund. This will take some time since they have a lot of requirements for applying. (see http://www.cowifonden.dk/Vejledning_for_ansoegere.asp)
• The ‘Fondeliste’ has been updated according to the funds that Anastasiya and Anja found in the beginning of June.
• A document called ‘Company applications’ can be found in the ‘company’ folder. Please write in that document if you send out a company application.
• An application to the fund ALECTIA has been send.

Birthday and fun day at the lab? (Maya, Anja, and Patrick) - 24/06/10

So today was yet another day in the lab, only difference being it was my birthday (Patrick). :D
The serial dillutions we plated of our transformants didnt seem to produce a substantial amount of colonies after having plated them yesterday, so we plated a 10-1 and a 10-2 dilution to get a higher number of colonies.
We purified plasmids from strain SP44, SP45 and SP46 using the miniprep kit, and ran the purified plasmids on a gel to check if our plasmid purification was efficient and successful. There is now a miniprep protocol in the protocol folder.
We also made some -80 freezing cultures of strain SP44-46. To keep track of the future freezing cultures we have made a document called strain bank which we should all use when we make some -80 cultures. It's in the research group-> strain and plasmid folder.
The O/N of SP58 didn't show any growth, so a new O/N was started.

Progress (Maya, Anja, and Patrick) - 23/06/10

So we started in the lab yesterday after having gotten all the needed information from Flemming concerning the FP's (fluorescence proteins).
We started constructing some template plasmids with FP's and markers, and so far its been a fun experience thanks to Hassan.
As things are now we have decided to use the fluorescent proteins mCherry and YGFP as the reporters, though the final template plasmids will include the fast-degradable fluorescent proteins of mCherry and YGFP.
Today we started O/N cultures of the following strains: SP44, SP45, SP46 and SP58. SP44-46 contains plasmids with CFP, yGFP and Cherry, and SP58 contains a plasmid with the markers CAM and KAN.
We also made a transformation using electroporation. We transformed plasmid pSLD3 into E.coli strain . pSLD3 is to be used as a recipient plasmid of markers and FPs. After the transformation, we made a serial dilution of the transformed strain and plated these. We have uploaded a transformation protocol in the research group folder- protocol folder.

iGEM the last 2 weeks - 21/06/10

So the last 2 weeks have been quite hectic and busy, and if you're wondering why there hasn't been an update its because alot of things keep coming up while working on the design.
The in-silico design is moving along well, though when every new step comes along we run into issues, just like today we realized that the UV system just might not work after all, long story short - because the excitation wavelength will interfere with the excitation wavelength of the red-light receptor. Solution: good old lov-tap will most likely come into the picture now.
In terms of the reporter genes, we were lucky enough to find Flemming back at CSM today, and so Maya and Juliet managed to get alot of good info from him about flourescence proteins which made us wiser in that area, although we also realized they arnt as straight forward to work with as initially thought, so we need to put in more work in that area as well.
We are set to get into the lab tomorrow to possibly start construction of the template plasmids with the flourescence proteins, that is of course if we have the FP's we want to work with and whether those have the appropriate degradation time.
That's about all for now, stay tuned for more exciting news in the days to come.

Maya, Anja, Malthe and Patrick's log - 08/06/10

We have finished the step-wise construction of our system, and have begun on the in-silico model.
We have uploaded the initial work from the in-silico model in a newly created folder in the research group called step-wise construction and in-silico model.

Maya and Patrick's log - 07/06/10

So today we have been working on the step-wise construction of our system, taking into account how to test each part along the way. We learned a lot about recombineering and the factors entailed in the process and have come up with the initial version of how we are going to construct the system.
As a rule of thumb we also learnt the following combinations and bad-combinations when working with FP's:

• RFP can be used together with either GFP or CFP; and YFP together with CFP.
• The bad combinations which we should never ever do are the following: RFP with YFP; and YFP with GFP.

Captain's log 040610

Maya, Thomas, Patrick, Lisa and Annemi have been working on a project description for Sebastien. The document 'project description' can be found in dropbox in the research group folder. From now on this document will be the only one describing the project, therefore you should edit in the document and not create a new one. We have decided that every time we are doing something iGEM related, that it should be posted in this document. Please write the date and your name at the beginning of your log. This will make it easier for all of us to keep track of what is going on in the group. We have tried to make a simple plan of what needs to be done before going to the lab:

• Investigate the E. coli chromosome to find out where we can integrate the switch
• Find the BioBricks we will be using (DNA sequences)
• Install the software CLC main workbench (the program which will be useful for the design of the system)
• Design the system: Order of genes, restriction sites, DNA sequences, order of integration of genes into the plasmids
• Which plasmids (Sebastien)
• Primer design
• How to test that the genes have been inserted (antibiotic resistance)
• Make a phase planning and talk to Peter (divide into smaller parts and and test these individually)

Maya will start creating an illustration for the system during the weekend. Thomas will delete all irrelevant budgets from the dropbox. He will also send the project description to Sebastien.