Team:Warsaw/Stage1/PromMeas

From 2010.igem.org

Revision as of 12:18, 26 October 2010 by Olchowik (Talk | contribs)

Example Tabs

Promoter measurement

Experimental setup

Measured parts

We have measured J23100 and I719005 encoding pT7.

J23100 with our reference RBS has RNA synthesis rate of 13,1pg RNA/minute/ug substrate DNA
pT7 with our reference RBS has RNA synthesis rate of 41,8pg RNA/minute/ug substrate DNA
Measurement constructs

We have used B0034 as our reference RBS and E0040 GFP as a reporter:

<partinfo>BBa_K299009 DeepComponents</partinfo>

<partinfo>BBa_K299024 DeepComponents</partinfo>

Results

Measured promoter strengths are as follows:

pT7 41,8pg RNA/minute/ug substrate DNA
J23100 13,1pg RNA/minute/ug substrate DNA

It means that for pT7 we put into cell-free system from ug of DNA polymerase made around 41 pg RBS in a one minute, is it a good unit for promoter activity? What happens if we input into our cell-free system DNA with the same biobrick, but in a different vector? The amount of DNA changes, but it doesn't change the number of available RBS. Therefore we have to change those units to something sound like numbers of RNA molecules made from 1 DNA molecule in a unit of time. Sounds like PoPs (polymerase per second) per DNA copy


How did we come up with those values...

We expressed known amount if DNA in a cell-free expression system and measured RNA content over time using RTq-PCR. Simply we put the DNA into the tube with the cell-free expression system and collected samples of the mixture every 15 minutes. Then we did the reverse transcription to be able to perform a q-PCR that gives information on the amount of starting material.
Figure 1 shows you the dynamic performance of J23100 and T7 promoters - the amount of RNA versus time. Figure 2 show amplification curves that we got after RTq-PCR.

Fig 1. Dynamic performance of J23100 and pT7.


Fig 2. The amplification curves that were obtained after RTq-PCR seperately for J23100 and T7 containing construct. Different colours indicate that samples were collected at different times: 15, 30. 45, etc. minutes after DNA addition. Dark blue is amplification curve for sample after 15 minutes and light blue is after 90, as you can see there is an increase in the RNA content.



Methodology

All measurements were conducted in cell-free system which allowed us simple and precise determination of GFP encoding mRNA. The amount of mRNA was determined using quantitative reverse transcriptase realtime PCR (qRT-PCR). We have done absolute quantification using cDNA standard curve to convert delta-Ct units to RNA concentration.

We have used following protocol:

  1. All reagents and substrates were RNase free. Experiments were conducted in RNase-free environment.
  2. 0.5 ug of DNA encoding tested construct was added to 50 ul of cell-free expression master mix containing 350 units of human placental RNase inhibitor.
  3. Samples were incubated at 37oC with shaking at 800 RPM
  4. Every 15 minutes 5ul of reaction mixture was collected. Reaction was stopped by freezing at -20. Samples were kept frozen until reverse transcription.
  5. Subsamples were being collected untill reaction have reached steady state (typically 120 minutes).
  6. After obtaining all RNA samples DNAse treatment was performed as follows: 5 ul of sample was supplemented with 1ul of 10x DNAse buffer, 3 ul of RNase-free water and 1ul of RNase-free DNase I from Fermentas
  7. Samples were incubated at 37oC for 30 minutes. After that time 1ul of EDTA was added to each sample.
  8. DNase was inactivated by heating in 65oC for 10 minutes.
  9. DNase treated RNA samples were divided in two. One half was used as a substrate for reverse transcription. The other halves were mixed together and used in -RT control reaction.
  10. Reverse transcription was performed using Maxima First Strand cDNA synthesis kit form Fermentas using manufacturer's instructions. Gene specific primer GFPqPCRr (TCGAAAGGGCAGATTGTG) was used.
  11. cDNA was diluted 50x and 1ul was used for qRT-PCR reaction. SYBR/ROX qPCR HotStart 2x Master Mix for Fermentas was used to perform the reaction with the following primers: GFPqPCRf (GATGACGGGAACTACAAGAC) and GFPqPCRr (TCGAAAGGGCAGATTGTG). ABI 7500 qPCR system was used. PCR program: 95oC for 10 minutes followed with 40 cycles of 95oC for 15s, 55oC for 30 s, 72oC for 40s. Reaction specificity was confirmed using melting curve analysis.