Team:UTDallas/Protocols

From 2010.igem.org

(Difference between revisions)
(Preparing Agar Plates Protocol (Makes 12 (15mm) Plates))
(Preparing Competent Cells Protocol)
Line 31: Line 31:
Note: Harvest cells at 5000 rpm for 10 minutes at 40<sup>o</sup>C
Note: Harvest cells at 5000 rpm for 10 minutes at 40<sup>o</sup>C
 +
 +
===Miniprep Protocol===
 +
*Harvest cells at 5400g  10 minutes 40<sup>o</sup>C  (possibly program 1)
 +
*Resuspend pelleted bacterial cells in 250 µL Buffer P1 and transfer to a microcentrifuge tube
 +
*Add 250 µL Buffer P2 and mix thoroughly by inverting the tube 4-6 times
 +
*Add 350 µL Buffer N3 and mix immediately and thoroughly by inverting the tube 4-6 times
 +
*Centrifuge for 10 minutes at 13000 rpm (~17900g) in a table-top microcentrifuge
 +
*Apply the supernatant (from step 4) to the QIA prep spin column by decanting or pipetting
 +
*Centrifuge for 30-60 seconds. Discard the flow-through
 +
*Wash QIA prep spin column by adding 0.75 mL Buffer PE and centrifuging for 30-60 seconds
 +
*Discard the flow-through, and centrifuge for 1 minute to remove residual wash buffer
 +
*To elute DNA, place the QIA prep column in a clean 1.5 mL microcentrifuge tube. Add 50 µL Buffer EB or water to the center of each QIA prep spin column, let stand for 1 minute and centrifuge for 1 minute.
</span>
</span>

Revision as of 16:21, 28 July 2010


Protocols

Preparing Agar Plates Protocol (Makes 12 (15mm) Plates)

  • 300 mL DI H2O + 11 g LB agar
  • Autoclave
    • Put control thermometer in H2O (from the sink)
    • Select vented container mode (Do Not Change Program)
  • Mix well after autoclaving; let cool to 50oC
  • Add antibiotic (50 to 100 µg/mL) (15 mg total)
    • Weigh on paper
    • Add to 0.5 mL DI H2O
    • Add to LB mixture when cool enough
  • Plate
    • Under flame open lids of all plates
    • Slowly pour agar into plate, avoiding bubbles, when it touches all edges stop pouring
    • Let sit under flames until gel solidifies
    • Replace lids on plates
  • Store upside down at 40oC

Preparing Competent Cells Protocol

  • Place 1 colony in 5 mL of LB (with antibiotics if appropriate) Grow overnight at 37oC and 200-300 rpm
  • Inoculate 0.25 mL of the overnight strain into 25 mL of LB
  • Shake at 37oC until the OD650 is 0.6-0.7
  • Harvest cells and resuspend in 12.5 mL ice cold 0.1M MgCl2
  • Harvest immediately and resuspend in 7.5 mL cold 0.1M CaCl2
  • Leave on ice for 30 minutes. Harvest and resuspend in 2.5 mL cold 0.1M CaCl2
  • Leave on ice for 30 minutes
  • For long term storage, use 0.1M CaCl2 in 15% glycerol at step 6 and store cells at -800oC

Note: Harvest cells at 5000 rpm for 10 minutes at 40oC

Miniprep Protocol

  • Harvest cells at 5400g 10 minutes 40oC (possibly program 1)
  • Resuspend pelleted bacterial cells in 250 µL Buffer P1 and transfer to a microcentrifuge tube
  • Add 250 µL Buffer P2 and mix thoroughly by inverting the tube 4-6 times
  • Add 350 µL Buffer N3 and mix immediately and thoroughly by inverting the tube 4-6 times
  • Centrifuge for 10 minutes at 13000 rpm (~17900g) in a table-top microcentrifuge
  • Apply the supernatant (from step 4) to the QIA prep spin column by decanting or pipetting
  • Centrifuge for 30-60 seconds. Discard the flow-through
  • Wash QIA prep spin column by adding 0.75 mL Buffer PE and centrifuging for 30-60 seconds
  • Discard the flow-through, and centrifuge for 1 minute to remove residual wash buffer
  • To elute DNA, place the QIA prep column in a clean 1.5 mL microcentrifuge tube. Add 50 µL Buffer EB or water to the center of each QIA prep spin column, let stand for 1 minute and centrifuge for 1 minute.