Team:Newcastle/research

From 2010.igem.org

Revision as of 13:15, 7 April 2010 by Jannetta (Talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

iGEM Homepage Newcastle University BacillaFilla Homepage Image Map

Contents

Caulobacter Crescentus Glue vs. Calcium Carbonate and Spider Silk

Injection

Steve & Zoltan

Concrete properties

Steve & Zoltan

Concrete has a high compressive strength (3000 to 4000 psi) and a very low tensile strength (between 8% to 15% of the compressive strength.). Cracking is due to the low tensile strength.

In reinforced concrete the steel reinforcement provides the tensile strength lacking in concrete. Steel has tensile strength equal to approximately 100 times that of concrete. Steel reinforcing is also capable of resisting compression forces.

Concrete and steel work very well together in relation to temperature changes because their coefficients of thermal expansion are quite close to each other. For steel it is 0.0000065 per unit length per degree Fahrenheit, while for concrete it is about 0.0000055.

Reference: Design of Reinforced Concrete 5th Edition, Jack C. McCormac.

Steven Woodhouse 19:23, 25 March 2010 (UTC)

Properties of calcium carbonate and spider silk

Calcium carbonate has a similar thermal expansion coefficient to concrete.

Some spider silks have a similar or better tensile strength than steel.

Glue, I haven't been able to find details of yet, but it is unlikely it has as good qualities.

Fibre-reinforced concrete. Addition of steel fibres (usually between 1% to 2% by volume) can appreciably improve their characteristics. Strength is not significantly improved, but significantly tougher and have greater resistance to cracking. The fibres used are usually from about ¼ inch up to about 3 inches with diameters of 0.01 inch up to 0.03 inches. While a reinforcing bar provides reinforcing only in the direction of the bar, randomly distributed fibres provide additional strength in all directions.

Recommendation at the moment: calcium carbonate with spider silk. Also, if we can get silk working it would give us some novelty vs. the other concrete projects we've found.

However: which silks have been sequenced? Is silk alkali-resistant?

Steven Woodhouse 19:24, 25 March 2010 (UTC)

Surface tension

Steve & Zoltan

If surface tension is a problem a surfactant could be produced by the bacteria or mixed into the spray.

Mixing bacteria into concrete

In a study done by Delft University of Technology (Jonkers et al., Application of bacteria as self-healing agent for the development of sustainable concrete), alkali-resistant spores were directly added to the concrete mixture prior to casting and remained viable for a period up to 4 months.

Incorporation of a high number of bacterial spores resulted in a decrease in compressive strength of less than 10% for 3, 7 and 28 days cured specimens. The incorporation of calcium lactate did not substantially affect strength (3 and 7 days cured) or even resulted in a slight increase (28 days cured) in compressive strength values.

Possible solutions to the loss of viability of the bacterial spores after 4 months are suggested in the paper.

Steven Woodhouse 20:55, 21 March 2010 (UTC)


In Use of bacteria to repair cracks in concrete, it was found that the bacteria had to be immobilised in silica gel to protect them from the high pH in concrete. Steven Woodhouse 17:15, 23 March 2010 (UTC)

Genetics

Harsh and Rachel

Nutrition and Plasmid vs genome

Bacillus subtilis spores

Alan and Da

Sporulation in Bacillus is governed by SpoOA that in turns activates over 100 genes involved in sporulation.

DNA replication have been linked to sporulation and is controlled by the AAA+ replication initiator protein DnaA. If there is disturbance in DNA replication, then DnaA will activate the sda gene encoding the sporulation inhibitor protein Sda.DnaA was shown to act as a positive regulator of sda transcription when DNA replication is perturbed. Thus,under conditions of replication stress, the Sda checkpoint prevents cells from initiating sporulation.

During each cell cycle the checkpoint protein Sda couples the initiation of DNA replication with the initiation of sporulation. Sda serves as a genetic timer that allows a window of opportunity toward the end of each replication cycle for Spo0A;P to reach the levels required to initiate sporulation, thus ensuring that a cell enters the sporulation pathway when it contains the correct copy number and has completed DNA replication and repair. Disruption of the coordination of replication and sporulation leads to an increase in the frequency of spores with more than one chromosome and a reduction in spore viability.

Therefore trageting or controlling Sda level maybe the key to obtaining high amount of spores, but at the same time running into the risks of low spores viability.


The paper, Bacillus subtilis spore coats in the drop box describle the process of sporulatuion with diagrams and various porteins involved.

Takes about 8h from the time of initiation of sporulation to complete spore formation.

Bacillus subtilis life cycle

Alan and Da

Low nutrient availability leads to low level of DnaA in the cells, therefore no chromosome replication. DnaA can also be regulated by Soj in Bacillus.

The bacterial cell cycle is divided into three stages: the period between division (cell ‘birth’) and the initiation of chromosome replication (known as the B period); the period required for replication (known as the C period); and the time between the end of replication and completion of division (known as the D period.)

Chromosome replication is governed by DnaA and is regulated by nutrient availability and also Soj. Cell division is regulated by the formation of FtsZ in mid-cell, leading to the formation the divisome.

The paper, Metabolism, cell growth and the bacterial cell cycle, provides nice diagrams on the process.