Team:Newcastle/31 August 2010

From 2010.igem.org

Revision as of 10:52, 31 August 2010 by Deenatsu (Talk | contribs)

iGEM Homepage Newcastle University BacillaFilla Homepage Image Map

Contents

Amplification of the plasmid PSB1C3 for rocF BioBrick

Aim

The aim of this experiment is to amplify plasmid linearized pSB1C3 for the construction of rocF BioBrick with the help of a single Phusion PCR using old primers.

Materials and Protocol

Please refer to PCR for Phusion PCR protocol. The details for the single PCR reaction is mentioned below:

PCR

Tube Part to be amplified DNA fragment consisting the part Forward primer Reverse Primer Melting Temperature (Tm in °C) Size of the fragment (in bp) Extension time* (in seconds)
1 Plasmid Vector pSB1C3 P1V1 forward P2V1 reverse 58 2072 approx. 65

Table 1: Table represents a single Phusion PCR reaction where plasmid pSB1C3 is amplified so that it can be ligated together with other rocF fragments with the help of Gibson Cloning method.

  • The extension rate of the Phusion polymerase is 1Kb/ 30 seconds. Thus the extension time of each and every PCR reaction is slightly different.
  • For learning about the rocF fragments, please refer to the Cloning strategy for rocF.

Discussion

The Phusion PCR reaction was done however, gel electrophoresis and gel extraction will take place today to check whether the fragments have actually amplified or not.

Conclusion

Today, we would be running gel electrophoresis to check the outcome of the PCR reaction and later all the fragments will be ligated with help of Gibson protocol.


Amplification of the parts for Subtilin Immunity BioBrick

Aim

The aim of this experiment is to amplify the four parts for the Subtilin Immunity BioBrick using Phusion PCR again but using the original primers that were ordered. (Before this could be done, four of the primers, 1-T1_for, 2-T1_rev, 1-P1_for and 2-P2_rev, had to be re-hydrated.)

For more information about the subtilin immunity BioBrick, please see the cloning strategy for subtilin immunity (Link)

Materials and Protocol

Please refer to Phusion PCR for Phusion PCR protocol. (Please refer to DNA Re-hydration for the DNA Re-hydration protocol.)

The details for the four PCR reactions are included in the table below:

Tube Part to be amplified DNA fragment consisting the part Forward primer Reverse Primer Melting Temperature (Tm in °C) Size of the fragment (in bp) Extension time* (in seconds)
1 Plasmid Vector PSB1C3 P1V1 forward P2V1 reverse 53.3 2046 + 70
2 Promoter and RBS (pVeg-SpoVG) BioBrick Bba_K143053 P1P1 forward P2P2 reverse 51.7 139 + 15
3 spaIFEG Gene Cluster B. subtilis ATCC 6633 P1S1 forward P2S1 reverse 46.0 2753 + 110
4 Double terminator pSB1AK3 consisting BBa_B0014 P1T1 forward P2T1 reverse 50.9 116 + 15

Table 2: This table shows the four different Phusion PCR reactions that were carried out today. If this is successful, the four parts will be ligated together for the construction of subtilin immunity BioBrick with the help of Gibson Cloning method.

  • The extension rate of the Phusion polymerase is 1 Kb/ 30 seconds. Thus the extension time of each and every PCR reaction is slightly different.

Results, Discussion and Conclusion

yneA

Single Digest

Aim

To do single digest of pGFPrrnB with Pst1 and Nhe1 to test if the enzymes are contaminated.

Materials and Protocol

Please refer to restriction digest and gel electrophoresis.

Results

Newcastle University logo.png    Newcastle cbcb logo.pngNewcastle Biomedicine logo.gif    Team Newcastle CEG logo.gif
Newcastle iww logo.jpg  UNIPV Pavia Logo.gif  Newcastle BBSRC.gif    Newcastle Genevision logo.png Newcastle WelcomeTrust.jpg
FaceBook Icon