Team:Edinburgh/Bacterial/Red light producer

From 2010.igem.org

(Difference between revisions)
m
Line 184: Line 184:
<br>
<br>
-
<a name="Characteristics" id="Characteristics"></a><h2>Problems</h2>
+
<a name="Characteristics" id="Characteristics"></a><h2>Characteristics</h2>
Two major points that need to be known when using this biobrick are the temperature sensitivity of the luciferase, and its pH sensitivity. During the first part of the project, the cells were grown at 37°C. When we tested growing them at 30°C, the temperature sensitivity  of the protein became evident, since the cells were a lot brighter. Rather than waiting 10 minutes in the dark room to get our eyes accustomed, they were visible before the door was closed.  
Two major points that need to be known when using this biobrick are the temperature sensitivity of the luciferase, and its pH sensitivity. During the first part of the project, the cells were grown at 37°C. When we tested growing them at 30°C, the temperature sensitivity  of the protein became evident, since the cells were a lot brighter. Rather than waiting 10 minutes in the dark room to get our eyes accustomed, they were visible before the door was closed.  
Line 192: Line 192:
<a name="Problems" id="Problems"></a><h2>Problems</h2>
<a name="Problems" id="Problems"></a><h2>Problems</h2>
<br>
<br>
-
<p>This part is one of the only ones with no major setbacks. The main problem will be attempting to activate the red light sensor with something that is not necessarily bright enough. RLUs are an arbitrary measurement and do not give a good enough indication of actual brightness for us to come to a conclusion on this yet. More characterisation is needed before this part can be used.</p>
+
<p>This part is one of the only ones with no major setbacks. The main problem will be attempting to activate the red light sensor with something which might not be bright enough. We did not have time to attempt this over the summer. If this does not work, it would be interesting to see if one can combine the codon optimised green luciferase which has been mutated for increased brightness with the mutations for red light.</p>
 +
 
 +
<p>Another evident problem is that the genes for luciferin production are not known and the luciferin needs to be added externally. But the firefly luciferase system is one of the most efficient bioluminescent systems known and when the genes required for luciferase production are known, this biobrick will surely be a great system for red light production. </p>
<br>
<br>
<br>
<br>

Revision as of 19:53, 26 October 2010







Overview: The red light producer


Firefly luciferase (EC 1.13.12.7) from Photinus pyralis is one of the most efficient bioluminescent proteins known. Its emission peak is about 557nm at pH 7.8 (this is the ordinary internal pH of E. coli during growth). We attempted to produce a mutant luciferase which would produce red light, in order to activate the red light sensor part (which responds optimally to 660nm light).

We used site-directed mutagenesis on the wild type to produce three different red light mutants:

  • Substitution mutant S284T
  • Insertion mutant 356K
  • Insertion mutant 356R


Figure 1: Emission spectra of the P. pyralis luciferase mutant S284T.

Image: Branchini et al. (2007)





Figure 2: Emission spectra of the P. pyralis luciferase mutants 356R (1) and 356K (2).

Image: Moradi et al. (2009)







Strategy


We successfully produced two red mutants of the firefly luciferase: Mutants 356K and S284T. Both of these glow a nice red colour, but S284T glows much brighter and should be used for work where red coloured bioluminescence is required. Measurements of bioluminescence / OD showed that the S284T luciferase glows at about 35% of the brightness of the wild type green one. The 356K luciferase glows significantly less and is very hard to see, even in a dark room.



Characteristics

Two major points that need to be known when using this biobrick are the temperature sensitivity of the luciferase, and its pH sensitivity. During the first part of the project, the cells were grown at 37°C. When we tested growing them at 30°C, the temperature sensitivity of the protein became evident, since the cells were a lot brighter. Rather than waiting 10 minutes in the dark room to get our eyes accustomed, they were visible before the door was closed.

pH sensitivity of the Photinus pyralis luciferase has been reported previously (Seliger and McElroy, 1964). The cells were usually suspended in citrate buffer, pH 4.8, as this allows the luciferin to enter the cells faster. This has an effect on the colour emitted, though not as marked as for the wild type.

Problems


This part is one of the only ones with no major setbacks. The main problem will be attempting to activate the red light sensor with something which might not be bright enough. We did not have time to attempt this over the summer. If this does not work, it would be interesting to see if one can combine the codon optimised green luciferase which has been mutated for increased brightness with the mutations for red light.

Another evident problem is that the genes for luciferin production are not known and the luciferin needs to be added externally. But the firefly luciferase system is one of the most efficient bioluminescent systems known and when the genes required for luciferase production are known, this biobrick will surely be a great system for red light production.



BioBricks


Our BioBricks for this component of the project consist of the two successfully mutated luciferases S284T and 356K, and their composite constructs.

BBa_K322246: firefly luciferase from Photinus pyralis, S284T mutant.

BBa_K322211: firefly luciferase from Photinus pyralis, 356K mutant.

BBa_K322247: S284T mutant luciferase under lac promoter

BBa_K322212: 356K mutant luciferase under lac promoter



Characterisation





Figure 2: Results of spectrum analysis of our S284T mutated firefly luciferase.



***





References


Branchini, B. R., Southworth, T. L., Khattak, N. F., Michelini, E. & Roda, A. (2005). Red- and green-emitting firefly luciferase mutants for bioluminescent reporter applications. Analytical Biochemistry 345, 140-148.

Branchini, B. R., Ablamsky, D. M., Murtiashaw, M. H., Uzasci, L., Fraga, H. & Southworth, T. L. (2007). Thermostable red and green light-producing firefly luciferase mutants for bioluminescent reporter applications. Analytical Biochemistry 361, 253-262.

Moradi, A., Hosseinkhani, S., Naderi-Manesh, H., Sadeghizadeh, M. & Alipour, B. S. (2009). Effect of Charge Distribution in a Flexible Loop on the Bioluminescence Color of Firefly Luciferases Biochemistry 48, 575-582.




Throughout this wiki there are words in bold that indicate a relevance to human aspects. It will become obvious that human aspects are a part of almost everything in iGEM.