Team:British Columbia/modeling results

From 2010.igem.org

Revision as of 02:29, 27 October 2010 by Sheizhan (Talk | contribs)



Simulation Results

The Binary Outcome


Biofilm Death


Figure 1: The simulated behavior of the biofilm and phage populations over 1200 mins (20 hrs). The percent of the total biofilm population remaining after phage introduction (blue) sharply declines at 400 min. This coincides with the sharp increase of the percent of the biofilm population infected by phage (green). The phage population (here, represented by the P-factor) peaks shortly after 400 mins. These features suggest that the accumulation of phage particles in the biofilm between 0 and 400 min triggers mass host cell lysis leading to the destruction of the biofilm at the 1200th min.



Figure 2: The dynamics of the extracellular concentrations of AIP (purple) and DspB (red) over 1200 mins (20 hrs). The maximum level of AIP concentration and the activation threshold level are indicated by the upper and lower dashed lines, respectively. AIP concentration is shown to steadily decrease over time, but does not fall below the threshold level during the 1200 mins. This is due to the relatively high rate of AIP degradation rate arbitrarily set for this simulation. DspB concentration rises rapidly at 400 min, coinciding with decrease in biofilm population and increase in phage population (indicated in Figure 1), and then peaks at 600 min when the biofilm population is substantially reduced.


Survival



Figure 3: The simulated behavior of the biofilm and phage populations over 1200 mins (20 hrs) in a system where DspB production is absent (i.e. S = 0). The phage population (orange) experiences rapid decline at the beginning, when the phage particles attempt to infect the bacteria at the surface of the biofilm, resulting in a small subpopulation of infected bacteria (green). However, the total biofilm population (blue) is minimally impacted. The relatively constant biofilm and phage populations suggest that the phage is repeatedly attempting infection at the biofilm surface but fails to penetrate into the biofilm structure. This simulation demonstrates that DspB greatly facilitates phage invasion into the biofilm structure, as shown in Collins et al. (2007).


Figure 4: The dynamics of the extracellular concentrations of AIP (purple) and DspB (red) over 1200 mins (20 hrs). The maximum level of AIP concentration and the activation threshold level are indicated by the upper and lower dashed lines, respectively. AIP concentration is shown to steadily decrease over time, but does not fall below the threshold level during the 1200 mins. This is due to the relatively high rate of AIP degradation rate arbitrarily set for this simulation. DspB is completely absent.

Sensitivity Analyses


Phage virulence is critical to successful biofilm dispersal
A


B

C

Figure 5: Sensitivity analysis of the phage infection rate parameter, κ. A range of values for the infection rate is used. The infection rate is shown to have some impact on the dynamics of the total biofilm population (panel A), the infected biofilm subpopulation (panel B), and the phage population (panel C). When the rate is high (>0.5), further rate increase has a diminishing effect on the population dynamics. When the rate is low (<0.2), further decrease may render the phage particles ineffective for biofilm degradation (panel A and B). This analysis suggests that the phage must be sufficiently virulent for biofilm dispersal to occur. Interaction between the phage and the target biofilm bacteria is an important component in the design of biofilm-degradation systems.

Half-life is not a main outcome-determining factor



Discussion

Although our model was initially developed to simulate the behavior of our genetically engineered (GE) system, it can be applied to predict the dynamics of other biofilm systems that are introduced to a biofilm matrix-degrading phage. By setting the model parameters to values that represent the properties of a real-world biofilm system, we can simulate scenarios where the biofilms are exposed to a GE phage functionally similar to ours. We can also incorporate information on the properties of the phage by modifying certain parameters. Below, we present results for simulations of medically relevant biofilm scenarios where GE phage may be considered for the therapeutic solution.